Order Amending the Steel Derivative Goods Surtax Remission Order, No. 1: SOR/2026-227

Canada Gazette, Part II, Volume 160, Number 22

Registration
SOR/2026-227 October 23, 2026

CUSTOMS TARIFF

P.C. 2026-1014 October 23, 2026

Her Excellency the Governor General in Council, on the recommendation of the Minister of Finance, makes the annexed Order Amending the Steel Derivative Goods Surtax Remission Order, No. 1 under section 115footnote a of the Customs Tarifffootnote b.

Order Amending the Steel Derivative Goods Surtax Remission Order, No. 1

Amendments

1 Section 3 of the Steel Derivative Goods Surtax Remission Orderfootnote 1 is replaced by the following:

Remission — goods referred to in Schedules 1 to 3

3 Subject to section 5, remission is granted of surtaxes paid or payable under the Steel Derivative Goods Surtax Order in respect of the goods referred to in any of Schedules 1 to 3.

2 Section 5 of the Order is replaced by the following:

Conditions

5 Remission is granted on the following conditions:

3 The schedule to the Order is replaced by the Schedules 1 to 3 set out in the schedule to this Order.

Coming into Force

4 This Order comes into force on the day on which it is registered.

SCHEDULE

(Section 3)

SCHEDULE 1

(Section 3 and paragraph 5(a))

Goods
Item

Column 1

Tariff Classification Number

Column 2

Good
1 3925.20.00 Doors, windows and their frames and thresholds for doors
2 7308.10.00 Bridges and bridge-sections, of iron or steel
3 7308.30.00.28 Motor-operated (gear head) rolling industrial galvanized steel service door, of specification ASTM 653, with coating of galvanized zinc or zinc-iron alloy (galvannealed) by hot-dip process, with slat and hood finish
4 7308.90.00
  • (a) Adapters for crossing gates, of steel, safety sensitive, with an assembled length of 32 inches, with an assembled width of 12 inches, with an assembled height of 7 inches;
  • (b) Glare screen systems, of 25-gauge steel sheet of grade AISI 1008 or 1010, hot-dip galvanized to ASTM A653 with a G90 coating and powder-coated, supplied with 0.75 inch attachment hardware, concrete expansion anchors and splice plates of 4140/42 steel with a thickness of 0.375 inch, with all hardware galvanized;
  • (c) Stamped or embossed door skins;
  • (d) Structural steel bottom bracket assemblies, fabricated as bent carbon steel plate assemblies, of specification ASTM A572 Grade 50, supplied with concrete screw anchors, with electro zinc plating conforming to ASTM B633;
  • (e) Structural steel foundation retrofit brackets, fabricated as welded assemblies from carbon steel plate, of specification ASTM A572 Grade 50, with a thickness of 0.25 inch, 0.3125 inch or 0.375 inch, with bolt holes and bearing surfaces, uncoated or hot-dip galvanized;
  • (f) Round structural steel tubes, welded, of specification ASTM A500 Grade C, with an outer diameter of 2.875 inches, with a wall thickness of 0.165 inch, with a length of 36 inches, galvanized;
  • (g) Steel couplers, welded, of specification ASTM A500 Grade B, with an outer diameter of 2.5 inches, with a wall thickness of 0.125 inches, with a length of 6 inches;
  • (h) External structural steel sleeves, welded, of specification ASTM A500 Grade B or C, with a flared end, with an outer diameter of 3.5 inches, with a wall thickness of 0.216 inches, with a length of 30 inches or 48 inches;
  • (i) Structural plate brackets, of carbon steel plate, of specification ASTM A36, with a thickness of 0.25 inches, with square dimension of 4.5 inches by 4.5 inches, with a welded cylindrical ring, with an outer diameter of 1.5 inches, with a wall thickness of 0.25 inches, with a length of 1.38 inches;
  • (j) Bent structural steel C-brackets, of carbon steel plate, of specification ASTM A36, with a thickness of 0.1875 inches, with bracket dimensions of 3.0 inches by 6.0 inches, with a welded cylindrical ring, with an outer diameter of 1.5 inches, with a wall thickness of 0.25 inches, with a length of 1.38 inches;
  • (k) Structural steel beam splice bracket assemblies, of specification ASTM A36, consisting of two plates with a welded cylindrical ring of steel tubing, with a wall thickness of 0.25 inches, with a length of 1.38 inches, supplied with four bolts with corresponding nuts;
  • (l) Threaded steel rods, of specification ASTM F1554 Grade 55, with a welded heavy hex nut, with a diameter of 1 inch, with a length of 8 inches;
  • (m) Structural steel threaded post caps, with internal threads, of specification ASTM A108 Grade 1018, with an outer diameter of 3.0 inches, with a thickness of 1.0 inch;
  • (n) Round structural steel tubing, welded, of specification ASTM A500 Grade C, with an external diameter of 2.88 inches, with a wall thickness of 0.165 inches, with a length of 36 inches, 60 inches or 84 inches, galvanized, with an internal zinc coating;
  • (o) Structural steel bottom plate assemblies, of specifications ASTM A36 and ASTM A500, consisting of a plate of grade ASTM A36 with a thickness of 0.25 inches and dimensions of 3.5 inches by 3.5 inches, with a welded hollow structural section of specification ASTM A500 Grade B, of square cross-section, with cross-sectional dimensions of 2.0 inches by 2.0 inches, with a wall thickness of 0.25 inches, with a length of 0.75 inches;
  • (p) Structural steel base plate assemblies, of specification ASTM A36, ASTM A513 Type 5 or ASTM A53 Grade B, consisting of a carbon steel plate with a steel pipe, with an outer diameter of at least 2.75 inches but not exceeding 3.38 inches, with a wall thickness of at least 0.156 inches but not exceeding 0.188 inches, with a length of 4.0 inches, electro zinc-plated, conforming to ASTM B633;
  • (q) Adjustable structural steel bridge bracket assemblies, of specification ASTM A572 Grade 50, consisting of plates with telescoping components, with an adjustable overall length of at least 13.5 inches but not exceeding 16.5 inches, with a beam capture plate, supplied with bolts, electro zinc-plated;
  • (r) Structural steel lever bracket and runner assemblies, of specification ASTM A572 Grade 50, consisting of a lever bracket and a runner strap, with a beam capture plate of specification ASTM A36, supplied with bolts, nuts and wood screws, electro zinc-plated;
  • (s) Hydraulic lift cylinder assemblies, linear acting, pressure ratings not exceeding 8000 psi, supplied with structural steel top plates of specification ASTM A572 Grade 50, rods and couplers, hydraulic hoses and fittings, control valves and fasteners;
  • (t) Steel fence panels, formed as continuous corral panels, consisting of five horizontal 14-gauge steel tubes, with an outside diameter of 1.25 inches, and vertical steel rods with an outside diameter of 0.75 inches, with a length of 20 feet, with a height of 4 feet, uncoated;
  • (u) Double-headed steel pickets, with a diameter of 1 inch, with a length of 40 inches, electroless nickel-plated;
  • (v) Highway crash attenuation systems, end terminals, crash terminals, crash cushions, high-tension cable barrier systems, temporary barrier systems and truck- and trailer-mounted attenuators, of steel, wood and polymer, tested to the National Cooperative Highway Research Program (NCHRP) Report 350 or the Manual for Assessing Safety Hardware (MASH) of the American Association of State Highway and Transportation Officials (AASHTO);
  • (w) Redirective, non-gating crash cushion assembly, consisting of high molecular weight/high density polyethylene (HMW/HDPE) energy-absorbing cylinders, mounted on a self-contained or concrete backup structure;
  • (x) Gating, flared end-terminal system for roadside W-beam guardrail applications, in 6-post or 8-post configurations;
  • (y) Tangent end-terminal for W-beam guardrail systems, consisting of galvanized steel components, including guardrail sections, extruder head, hardware and posts
5 7308.90.00.70 Girders and similar structural units, of steel
6 7308.90.00.95 Grills, air diffusers or ducts of iron or steel
7 7308.90.00.99
  • (a) Turnbuckle stud assemblies for cable-barrier systems, of steel, including threaded stud and nut, with a diameter of 1 inch, with a length of 7.87 inches, galvanized;
  • (b) Cable spacers for cable-barrier systems, of steel, with a length of 0.15 m, galvanized;
  • (c) Sleeve covers for cable-restraint system posts, of steel, with a width of 0.15 m, with a length of 0.2 m, hot-dip galvanized;
  • (d) Dust covers for cable-restraint system posts, of steel, with a diameter of 180 mm, with a depth of 50 mm, galvanized;
  • (e) Cable-barrier posts, of carbon steel, with a nominal height of 5.7 feet, with a length of 1.52 m, 10-gauge, galvanized;
  • (f) Short posts for cable-barrier systems, of carbon steel, with a length of 1.2 m, galvanized;
  • (g) Post straps for cable-barrier systems, of steel, with a thickness of 6 mm, galvanized;
  • (h) Post caps for cable-barrier systems, of steel, stamped, with a nominal height of 7.7 feet, with a width of 0.15 m, with a length of 0.15 m, hot-dip galvanized;
  • (i) Washers, of carbon steel, with an inner diameter of 0.31 inches, with a zinc coating;
  • (j) Washers, of hardened steel, of specification ASTM F436, with a diameter of 0.75 inches;
  • (k) Hex nuts, of steel, of specification ASTM A194 2H, with a diameter of 0.75 inches;
  • (l) Hex bolts, of steel, of specification ASTM A307, with a diameter of 0.31 inches, with a length of 1.75 inches;
  • (m) Structural hex bolts, of steel, of specification ASTM A325, with a diameter of 0.75 inches, with a length of 4.50 inches;
  • (n) Post straps, of steel, with a thickness of 6 mm, with a length of 0.2 m, galvanized;
  • (o) Hook bolts, of steel, with threaded section and formed hook end, with a diameter of 0.31 inches, with a length of 1.75 inches, for use with cable-barrier post assemblies;
  • (p) Guardrail offset blocks or king blocks, of high-density polyethylene (HDPE), with a thickness of 4 inches, with a height of 7.5 inches, with a length of 14 inches;
  • (q) Cable lock bolts, of steel, with a locking head for cable retention, with a diameter of 0.31 inches, for use in cable-barrier assemblies;
  • (r) Lower posts for cable restraint system, of galvanized steel, with a length of 84 inches, for use in roadside barrier systems;
  • (s) Post caps, of steel, stamped, with a width of 150 mm, with a length of 150 mm, galvanized;
  • (t) Washers, of hardened steel, of specification ASTM F436, with a diameter of 1 inch;
  • (u) Retroflective panels, of steel, with a width of 5 inches, with a length of 24 inches, galvanized or coated;
  • (v) Cable stud assemblies, of steel, with a diameter of 25 mm, machined threads;
  • (w) Terminal posts, of steel, for Test Level 4 (TL-4) barrier systems, with a length of 71.62 inches, galvanized;
  • (x) Driven sleeves, of steel, with a wall thickness of 0.19 inches and with a length of 30.75 inches, galvanized;
  • (y) Base angles for cable anchor, of steel, with a thickness of 12 mm, with a width of 150 mm, with a length of 150 mm, galvanized;
  • (z) Cable-restraint post brackets, of steel, with a thickness of 6 mm;
  • (z.1) Line posts for a cable-control terminal, of steel, galvanized;
  • (z.2) Cable-restraint posts, of steel, galvanized, with a length of 0.61 m, supplied as an upper release-post assembly;
  • (z.3) End terminals for roadside guardrail systems, of steel, meeting MASH Test Level 3 performance criteria, consisting of posts, release hardware and anchorage components;
  • (z.4) Hex nuts, of carbon steel, of specification ASTM A563, with a diameter of 0.31 inches;
  • (z.5) Hex nuts, of steel, of specification ASTM A194 2H, with a diameter of 1 inch;
  • (z.6) Insulated metal panels, consisting of two profiled steel facings bonded to a rigid polyisocyanurate foam core, with a width of 40 inches, with a thickness of 3 inches or 4.5 inches, with a length of at least 96 inches but not exceeding 374 inches, with a polyvinylidene fluoride (PVDF) coating on the exterior facing and a polyester coating on the interior facing;
  • (z.7) Insulated structural panels, consisting of a mineral-wool core bonded to steel facings of 22-gauge, 24-gauge or 26-gauge thickness, with a width of 42 inches or 43 inches, with a length of at least 8 feet but not exceeding 48 feet, with a thickness of 3 inches or of at least 4 inches but not exceeding 8 inches;
  • (z.8) Malleable cast iron slip-on pipe clamp fittings of grade BS 340/12 equivalent or grade 420/12 equivalent, produced by malleable iron casting, non-threaded, with nominal pipe diameters of 0.75 inches, 1 inch, 1.25 inches, 1.5 inches or 2 inches, including pre-installed set screws, fluorocarbon coated;
  • (z.9) Forged low-alloy steel integral wellhead casing spool of grade AISI 4130 / UNS G41300, of specification API 6A PSL-3, API 20B or API 20C and NACE MR0175 / ISO 15156, electric-furnace melted, forged, normalized, quenched and tempered, with an outer diameter of 584 mm, an overall length of 670 mm, a through-bore diameter of 276 mm, a weight of 623 kg (1374 lb), with 279 mm studded flange top and bottom connections and two 52 mm studded side outlets, no surface coating;
  • (z.10) Forged low-alloy steel oilfield tubing head of grade AISI 4130 / UNS G41300, of specification API 6A PSL-1, API 20B or API 20C and NACE MR0175 / ISO 15156, electric-furnace melted, forged, normalized, quenched and tempered, with a through-bore diameter of 164 mm (6.45 inches), an overall length of 359 mm (14.12 inches), with a 179 mm (7-1/16 inch) flange top connection, a 178 mm slip-on-weld bottom connection and two 51 mm threaded side outlets, semi-finished, no surface coating;
  • (z.11) Forged low-alloy steel oilfield tubing head assembly with offset bore and angled outlet configuration of grade AISI 4130 / UNS G41300, of specification API 6A, API 20B or API 20C and NACE MR0175 / ISO 15156, electric-furnace melted, forged, normalized, quenched and tempered, with a 279 mm (11 inches) studded flange bottom connection, a 179 mm (7-1/16 inch) flange top connection positioned on a 36 mm (1.40 inches) offset centre line and two 52 mm (2-1/16 inch) studded side outlets, semi-finished, no surface coating;
  • (z.12) Forged low-alloy steel oilfield tubing head with metal-to-metal slip-lock seal lower connection of grade AISI 4130 / UNS G41300, of specification API 6A PSL-2, API 20B or API 20C and NACE MR0175 / ISO 15156, electric-furnace melted, forged, normalized, quenched and tempered, with a through-bore diameter of 226 mm (8.88 inches), an overall length of 422 mm (16.62 inches), with a 279 mm (11 inches) flange top connection, a 244 mm (9-5/8 inch) outside-engagement metal-seal lower connection and two 52 mm (2-1/16 inch) extended-flange side outlets, semi-finished, externally treated with manganese or zinc phosphate conversion coating;
  • (z.13) Forged low-alloy steel oilfield tubing head assembly with offset upper bore and integrated secondary tubing head outlet of grade AISI 4130 / UNS G41300, of specification API 6A, API 20B or API 20C and NACE MR0175 / ISO 15156, electric-furnace melted, forged, normalized, quenched and tempered, with a 279 mm (11 inches) studded flange bottom connection, a 179 mm (7-1/16 inch) flange top connection on a 30 mm (1.188 inches) offset centre line, one 79 mm (3-1/8 inch) secondary tubing head outlet inclined 9 degrees with metal-to-metal seal profile and two 52 mm (2-1/16 inch) extended-flange side outlets, semi-finished, externally treated with phosphate conversion coating;
  • (z.14) Carbon steel cable splice assemblies for 3x7 wire rope, consisting of forged splice body, threaded rods and nuts, of grade ASTM A572, AISI 1045, ASTM F1554 Grade 55, ASTM F1554 Grade 105, ASTM A563 or ASTM A194, of specification ASTM A741, forged and stamped, case-hardened, with a splice body diameter of at least 64 mm, with a length of at least 191 mm but not exceeding 991 mm, galvanized to ASTM A153;
  • (z.15) Carbon steel sleeves for high tension cable barrier systems, of grade ASTM A500 Grade B, of specification AASHTO M270, formed and machined, with a cross-section of 127 mm by 83 mm and with a length of 781 mm, with a cross-section of 102 mm by 76 mm and with a length of 781 mm, or with a cross-section of 76 mm by 102 mm and with a length of 1067 mm, hot-dip galvanized to ASTM A123;
  • (z.16) Carbon steel bar grating panels of grade A36, of specification ANSI/NAAMM MBG 531 or MBG 532, with a smooth or serrated surface, with a bearing bar depth of at least 0.75 inches but not exceeding 4 inches, with a bearing bar thickness of at least 0.125 inches but not exceeding 0.375 inches, with a bearing bar spacing of 19/16 inches and with a cross bar spacing of 2 inches or 4 inches, with a width of at least 2 feet but not exceeding 3 feet and with a length of at least 20 feet but not exceeding 24 feet, bare or hot-dip galvanized to ASTM A123;
  • (z.17) Stainless steel bar grating panels of grade 304 or 316, of specification ASTM A240 and ANSI/NAAMM MBG 531, with a smooth or serrated surface, with a bearing bar depth of at least 1 inch but not exceeding 2 inches, with a bearing bar thickness of at least 0.125 inches but not exceeding 0.187 inches, with a bearing bar spacing of 19/16 inches and with a cross bar spacing of 4 inches, with a width of 3 feet and with a length of at least 20 feet but not exceeding 24 feet, mill finish or electropolished;
  • (z.18) Carbon steel or stainless steel (grade 316) channel grating end plates, of specification ASTM A1008 or ASTM A240, with a thickness of at least 3/16 inches but not exceeding 1/4 inch, with a width of at least 1 1/2 inches but not exceeding 2 inches and with a length of at least 4 3/4 inches but not exceeding 12 inches, with round hole of 7/16 inch and slot hole of 7/16 inch by 1 3/8 inches, galvanized to ASTM A123 or electropolished;
  • (z.19) Steel rings, of grade S355NL-Z25 or S420NL-Z25, of specification DIN EN 10025-3, with an outer diameter of at least 3268 mm but not exceeding 4750 mm, with an inner diameter of at least 3088 mm but not exceeding 3927.5 mm, with a thickness of at least 107 mm but not exceeding 432 mm
8 7312.10.00
  • (a) Wire hanging system and gripping mechanisms designed to work together to support HVAC ductwork installations with wire containing a red filament woven in, meeting SMACNA standards, seismic tested conforming to ICC Code guidelines AC284;
  • (b) Steel ropes and cables, containing from 6 to 35 strands, new, of rope grade 1960, 2160 or 2400, of a diameter of at least 3.18 mm but not exceeding 63.50 mm, whether ungalvanized, galvanized or plastic-coated
9 7312.10.00.22
  • (a) Custom profiled steel wire used to manufacture automotive wheel balancing weights (designed to adhere to the inside of the wheel using double-sided foam tape), made of low-carbon steel grade 1006, with dimensions of 0.120 × 0.598 x 0.690 inches, supplied in coil form;
  • (b) Custom profiled steel wire used to manufacture automotive wheel balancing weights (designed to adhere to the inside of the wheel using double-sided foam tape), made of low-carbon steel grade 1006, with dimensions of 0.120 × 0.498 × 0.787 inches, supplied in coil form;
  • (c) Stranded wire of non-alloy steel of specification ASTM A416, cold-drawn, stress-relieved, of grade 270, stranded in 1x7 construction, with a nominal diameter of at least 9.3 mm but not exceeding 15.2 mm, uncoated, epoxy-coated or galvanized;
  • (d) Stranded wire of non-alloy steel of specification ASTM A416, cold-drawn, stress-relieved, of grade 270, stranded in 1x7 construction, with a diameter of 12.7 mm, uncoated, epoxy-coated or galvanized;
  • (e) Stranded wire of non-alloy steel of specification ASTM A416, cold-drawn, stress-relieved, of grade 270, stranded in 1x7 construction, with a diameter of 15.2 mm, uncoated, epoxy-coated or galvanized;
  • (f) Stranded wire of non-alloy steel of specification A416/A416M-17a, of grade 270, of a diameter exceeding 5 mm
10 7312.10.00.31
  • (a) High carbon steel stranded wire ropes of grade 220, of specification modified EN 10138 Class A, stranded in 1x7 construction, cold drawn and stress relieved, with a diameter of 0.3125 inches and a reel length of 8500 feet, galvanized with a coating mass not exceeding 60 g/m2;
  • (b) High carbon steel stranded wire ropes of grade 220, of specification modified EN 10138 Class A, stranded in 1x7 construction, cold drawn and stress relieved, with a diameter of 0.3125 inches and a reel length of 6000 feet, galvanized with a coating mass not exceeding 60 g/m2;
  • (c) High carbon steel stranded wire ropes of grade 220, of specification modified EN 10138 Class A, stranded in 1x7 construction, cold drawn and stress relieved, with a diameter of 0.375 inches and a reel length of 7000 feet, galvanized with a coating mass not exceeding 60 g/m2;
  • (d) High carbon steel stranded wire ropes of grade Extra Improved Plow Steel (EIPS), of specification EN 12385, stranded in 6x19 class FC construction with fibre core, spheroidized annealed, with a diameter of 0.625 inches and a reel length of 5000 feet, galvanized;
  • (e) High carbon steel stranded wire ropes of grade EIPS, of specification EN 12385, stranded in 6x19 class FC construction with fibre core, spheroidized annealed, with a diameter of 0.75 inches and a reel length of 5000 feet, galvanized;
  • (f) High carbon steel stranded wire ropes of grade EIPS, of specification EN 12385, stranded in 6x19 class FC construction with fibre core, spheroidized annealed, with a diameter of 0.875 inches and a reel length of 5000 feet, galvanized;
  • (g) New swage compacted stranded steel wire rope, 4-strand semi-rotation-resistant construction, K4xK36-FC construction, bright or galvanized finish, with a nominal diameter not over 25 mm, Tensile Strength: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (h) New strand compacted stranded steel wire rope, 6-strand, 6xk31 WS or 6xK36 WS construction, fibre core or independent wire rope core, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (i) New stranded steel wire rope, 6-strand, 6x19 Seale or 6x26 WS construction, fibre core or independent wire rope core, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (j) New stranded steel wire rope, 6-strand, 6x36 WS construction, fibre core, bright or galvanized finish, with a nominal diameter not over 25 mm; Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (k) New stranded steel wire rope, 6-strand, 6x36 WS construction, independent wire rope core, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (l) New swaged stranded steel wire rope, 6-strand, K6x31WS-IWRC or K6x36WS-IWRC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M or DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (m) New stranded galvanized aircraft cable, 7x7 or 7x19 construction, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (n) New strand compacted stranded steel wire rope, 8-strand, 8xK19S-PWRC(K) or 8xK26WS-PWRC(K) construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (o) New stranded steel wire rope, 8-strand, 8x19S-IWRC, 8x25F-IWRC, 8x26WS-IWRC, 8x31WS-IWRC, 8x36WS-IWRC or 8x41WS-IWRC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (p) New stranded steel wire rope, 8-strand, 8x25F-EPIWRC, 8x36WS-EPIWRC or 8x41WS-EPIWRC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (q) New strand compacted stranded steel wire rope, 8-strand, 8xK19S-EPIWRC, 8xK26WS-EPIWRC, 8xK31WS-EPIWRC, 8xK36WS-EPIWRC or 8xK41WS-EPIWRC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (r) New stranded steel wire rope, 8-strand, 8xK19S-IWRC or 8x36WS-IWRC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (s) New strand compacted stranded steel wire rope, 8-strand, 8xK26WS-PWRC(K)(EP), 8xK31WS-PWRC(K)(EP), 8xK36WS-PWRC(K)(EP) or 8xK41WS-PWRC(K)(EP) construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (t) New strand compacted stranded steel wire rope, 8-strand, 8xK31WS-IWRC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M, supplied on reels or cut lengths;
  • (u) New swage compacted stranded steel wire rope, 8-strand, K8x25F-EPIWRC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (v) New swage compacted stranded stainless steel wire rope, 4 outer strands, K4x19S-SFC construction, Stainless Steel Type AISI 304 - 1.4301, with a nominal diameter not over 25 mm; Tensile Strength: at least 1570 MPa but not exceeding 1770 MPa; Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (w) New stranded stainless steel aircraft cable, 7-strand, 7x7 or 7X19 construction, Stainless Steel Type 304 or 316, with a nominal diameter not over 25 mm; Tensile Strength: at least 1550 MPa but not exceeding 2210 MPa; Specification: RR-W-410; supplied on reels or cut lengths;
  • (x) New stranded stainless steel wire rope, 6-strand, 6x36 WS construction, independent wire rope core, Stainless Steel Type 304 or 316, with a nominal diameter not over 25 mm; Tensile Strength: at least 1550 MPa but not exceeding 2210 MPa; Specification: RR-W-410; supplied on reels or cut lengths;
  • (y) Galvanized carbon steel wire rope of grade Improved Plow Steel (IPS) or EIPS, of specification FS-RR-W410J or ASTM A1023, 6x19 construction with fibre core or independent wire rope core, preformed, right hand regular lay, with a diameter of at least 1/2 inch but not exceeding 3/4 inch, with a length of at least 2400 feet but not exceeding 3600 feet, heavy galvanized, lubricated;
  • (z) High carbon steel stranded wire ropes of specification AASHTO M30 and ASTM A741, 3x7 stranded, preformed, right regular lay, factory pre-stretched, with a diameter of 0.75 inches and with a length of 600 m or 1200 m, galvanized to Type 1 Class A
11 7312.10.00.32
  • (a) New swage compacted stranded steel wire rope, 4-strand semi-rotation-resistant construction, K4xK36-FC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (b) New strand compacted stranded steel wire rope, 6-strand, 6xk31 WS or 6xK36 WS construction, fibre core or independent wire rope core, bright or galvanized finish, over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (c) New stranded steel wire rope, 6-strand, 6x19 Seale or 6x26 WS construction, fibre core or independent wire rope core, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (d) New stranded steel wire rope, 6-strand, 6x36 WS construction, fibre core, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (e) New stranded steel wire rope, 6-strand, 6x36 WS construction, independent wire rope core, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (f) New swaged stranded steel wire rope, 6-strand, K6x31WS-IWRC or K6x36WS-IWRC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M or DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (g) New stranded steel wire rope, 8-strand, 8x19S-IWRC, 8x25F-IWRC, 8x26WS-IWRC, 8x31WS-IWRC, 8x36WS-IWRC or 8x41WS-IWRC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (h) New stranded steel wire rope, 8-strand, 8x25F-EPIWRC, 8x36WS-EPIWRC or 8x41WS-EPIWRC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (i) New strand compacted stranded steel wire rope, 8-strand, 8xK19S-EPIWRC, 8xK26WS-EPIWRC, 8xK31WS-EPIWRC, 8xK36WS-EPIWRC or 8xK41WS-EPIWRC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: IPS (1770), EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (j) New stranded steel wire rope, 8-strand, 8xK19S-IWRC or 8x36WS-IWRC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (k) New strand compacted stranded steel wire rope, 8-strand, 8xK26WS-PWRC(K)(EP), 8xK31WS-PWRC(K)(EP), 8xK36WS-PWRC(K)(EP) or 8xK41WS-PWRC(K)(EP) construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (l) New strand compacted stranded steel wire rope, 8-strand, 8xK31WS-IWRC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (m) New swage compacted stranded steel wire rope, 8-strand, K8x25F-EPIWRC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (n) New stranded stainless steel wire rope, 6-strand, 6x36 WS construction, independent wire rope core, stainless steel of grade 304 or 316, with a nominal diameter over 25 mm but not over 50 mm, of a tensile strength of at least 1410 MPa but not exceeding 2450 MPa, of specification RR-W-410; supplied on reels or cut lengths
12 7312.10.00.33
  • (a) New stranded steel wire rope, 6-strand, 6x36 WS, 6x41 WS or 6x49 WS construction, independent wire rope core, bright or galvanized finish, with a nominal diameter over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (b) New stranded steel wire rope, 8-strand, 8x19S-IWRC, 8x25F-IWRC, 8x26WS-IWRC, 8x31WS-IWRC, 8x36WS-IWRC or 8x41WS-IWRC construction, bright or galvanized finish, with a nominal diameter over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (c) New stranded steel wire rope, 8-strand, 8x25F-EPIWRC, 8x36WS-EPIWRC or 8x41WS-EPIWRC construction, bright or galvanized finish, with a nominal diameter over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (d) New strand compacted, stranded steel wire rope, 8-strand, 8xK19S-EPIWRC, 8xK26WS-EPIWRC, 8xK31WS-EPIWRC, 8xK36WS-EPIWRC or 8xK41WS-EPIWRC construction, bright or galvanized finish, with a nominal diameter over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (e) New strand compacted, stranded steel wire rope, 8-strand, 8xK26WS-PWRC(K)(EP), 8xK31WS-PWRC(K)(EP), 8xK36WS-PWRC(K)(EP) or 8xK41WS-PWRC(K)(EP) construction, bright or galvanized finish, with a nominal diameter over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths
13 7312.10.00.41
  • (a) New swage compacted stranded steel wire rope, 10 outer strands, category III rotation-resistant, K10x19S-EPIWRC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (b) New strand compacted stranded steel wire rope, 10 outer strands, 10xK31WS-EPIWRC(K) construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (c) New swage compacted stranded steel wire rope, 10 outer strands, K10x19S-PWRC or K10x25F-PWRC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (d) New stranded steel wire rope, 12 outer strands, category II rotation-resistant, 17x7 WSC, 18x7 WSC, 19x7-WSC, 18x19 WSC or 19x19 WSC, construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (e) New stranded steel wire rope, 16 outer strands, category I rotation-resistant, 29(W)xK7-KWSC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (f) New strand compacted stranded steel wire rope, 18 total strands, category II rotation-resistant, 18 x K19-KWSC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (g) New strand compacted stranded steel wire rope, 35 total strands, category I rotation-resistant, 35(W) x K7-KWSC, 35(W) x K17S-KWSC, 35(W) x K19W-KWSC or 35(W) x K25F-KWSC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (h) New stranded steel wire rope, 9 outer strands, 9x19S-PWRC or 9x25F-PWRC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (i) New swage compacted stranded steel wire rope, 9 outer strands, K9x19S-PWRC or K9x25F-PWRC construction, bright or galvanized finish, with a nominal diameter not over 25 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (j) New stranded stainless steel wire rope, 12 outer strands, category II rotation-resistant, 19x7-WSC construction, stainless steel of grade 304, with a nominal diameter not over 25 mm; Tensile Strength: at least 1550 MPa but not exceeding 2450 MPa; Specification: RR-W-410; supplied on reels or cut lengths
14 7312.10.00.42
  • (a) New swage compacted stranded steel wire rope, 10 outer strands, category III rotation-resistant, K10x19S-EPIWRC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (b) New strand compacted stranded steel wire rope, 10 outer strands, 10xK31WS-EPIWRC(K) construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (c) New swage compacted stranded steel wire rope, 10 outer strands, K10x19S-PWRC or K10x25F-PWRC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (d) New stranded steel wire rope, 12 outer strands, category II rotation-resistant, 17x7 WSC, 18x7 WSC, 19x7-WSC, 18x19 WSC, or 19x19 WSC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M; supplied on reels or cut lengths;
  • (e) New stranded steel wire rope, 16 outer strands, category I rotation-resistant, 29(W)xK7-KWSC or 29(W)xK17S construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (f) New strand compacted stranded steel wire rope, 18 total strands, category II rotation-resistant, 18 x K19-KWSC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (g) New strand compacted stranded steel wire rope, 35 total strands, category I rotation-resistant, 35(W) x K7-KWSC, 35(W) x K17S-KWSC, 35(W) x K19W-KWSC or 35(W) x K25F-KWSC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (h) New stranded steel wire rope, 9 outer strands, 9x19S-PWRC or 9x25F-PWRC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: ASTM A1023/1023M or DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (i) New swage compacted stranded steel wire rope, 9 outer strands, K9x19S-PWRC or K9x25F-PWRC construction, bright or galvanized finish, with a nominal diameter over 25 mm but not over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths
15 7312.10.00.43
  • (a) New strand compacted, stranded steel wire rope, 10 outer strands, 10xK31WS-EPIWRC(K) construction, bright or galvanized finish, with a nominal diameter over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (b) New strand compacted, stranded steel wire rope, 35 total strands, category I rotation-resistant, 35(W) x K7-KWSC, 35(W) x K17S-KWSC, 35(W) x K19W-KWSC or 35(W) x K25F-KWSC construction, bright or galvanized finish, with a nominal diameter over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths;
  • (c) New stranded steel wire rope, 16 outer strands, category I rotation-resistant, 29(W) x K17S-KWSC, 29(W) x K19W-KWSC or 29(W) x K25F-KWSC construction, bright or galvanized finish, with a nominal diameter over 50 mm; Tensile Strength Grade: EIPS (1960) or EEIPS (2160); Manufacturing Standard: DIN EN 12385-1/2/4; supplied on reels or cut lengths
16 7312.90.00 Steel wire rope and strand assemblies, fitted with end terminations, new, of a diameter of at least 57.15 mm but not exceeding 127.00 mm, whether ungalvanized, galvanized or plastic-coated
17 7314.14.00
  • (a) Woven wire micronic filtering mesh, ASTM E2016 stainless steel (grade 304 or 316) roll, mesh openings range from 4 to 800 per inch, mesh diameter ranges from 0.0016 inches to 0.10 inches, dimension ranges from 36 inches to 48 inches wide by 100 feet long, weave type: plain Dutch weave or twill Dutch weave, mill finish;
  • (b) Woven wire ASTM E2016 stainless steel (grade 304) roll, opening size ranges from 2 to 370 mesh openings per inch, wire diameter ranges from 0.0010 inches to 0.080 inches, dimension ranges from 48 inches to 60 inches or 60 inches to 72 inches wide by 100 feet long, weave type: press-lock crimp, intercrimp, lockcrimp, plain crimp, plain weave, twill weave, mill finish;
  • (c) Woven wire ASTM E2016 stainless steel (grade 347) roll, 8 mesh wire openings per inch, 0.063 inches wire diameter, dimensions: 4 feet wide by 100 feet long, weave type: plain crimp, mill finish
  • (d) Woven stainless steel wire cloth (mesh), of cold-drawn stainless steel wire of grade AISI 304 or AISI 316, produced using plain weave, twill weave or Dutch weave, including reverse Dutch, with a wire diameter of at least 0.025 mm but not exceeding 0.500 mm, with a mesh count of at least 20 but not exceeding 400 wires per inch, with a mesh count tolerance of ±2%, with a width of at least 24 inches but not exceeding 60 inches, cleaned and degreased, in rolls or slit strips
18 7314.20.00 Modular welded wire mesh security walls of steel, with steel tube posts and hinged doors, powder-coated finish
19 7314.42.00 PVC-coated galvanized carbon steel wire mesh for lobster traps, of specification ASTM A1064 and ASTM A641, with a wire diameter before coating of 0.099 inches (12.5 gauge) or 0.128 inches (10.5 gauge), PVC coated over zinc galvanization
20 7314.50.00
  • (a) ASTM F1267 expanded metal grating stainless steel (grade 304), Short opening dimension is 1.33 inches, long opening dimension is 5.33 inches, load rating: 3 lbs/square foot, dimensions: 48 inches wide by 96 inches long, minimum 300 lbs;
  • (b) ASTM F1267 expanded metal sheets, stainless steel (grade 304 or 316), short opening dimension ranges from 0.187 inches to 1.500 inches, long opening dimension ranges from 0.500 inches to 3.000 inches, metal thickness ranging from 0.026 inches to 0.140 inches, flat or raised style, dimensions: 48 inches wide by 96 inches long
21 7315.11.00
  • (a) Roller chain of carbon, alloy or stainless steel, of specification ANSI/ASME B29.1, including simplex roller chains, heavy roller chains, duplex chains, double pitch drive chains, double pitch conveyor chains and agricultural CA-type chains, with a pitch of at least 6 mm but not exceeding 101.6 mm, with a link plate height of at least 6 mm but not exceeding 47.8 mm and with a pin diameter of at least 2.31 mm but not exceeding 19.85 mm, uncoated, zinc-flake coated or nickel plated;
  • (b) Roller chain coils or connecting links of grade 4140, of specification ANSI B29.1, cold-rolled, with a length of at least 27 inches but not exceeding 27.04 inches, oiled;
  • (c) Roller chain coils of grade 4140, of specification ANSI B29.1, cold-rolled, with a length of at least 27 inches but not exceeding 27.04 inches, nickel plated;
  • (d) Roller chain of carbon steel, alloy steel or stainless steel of specification ANSI B29.1, ISO 606B, BS 228 or DIN 8187, assembled, with an inner link width of at least 0.125 inches but not exceeding 1.875 inches, with a roller diameter of at least 0.13 inches but not exceeding 2.25 inches and with a pitch of at least 0.25 inches but not exceeding 4 inches, rustproofed, nickel plated, zinc plated or treated;
  • (e) Roller chain of specification ANSI 2080, with a pitch of 2 inches, 1 row, heavy duty, with a length of 10 feet, of stainless steel;
  • (f) Roller chain of specification ANSI 2160, with a pitch of 2 inches, 1 row, heavy duty, with a length of 10 feet, with attachment;
  • (g) Roller chain of specification ANSI 40, with a pitch of 1/2 inch, 1 row with 25 links, without connecting link;
  • (h) Roller chain of specification ANSI 41, with a pitch of 1/2 inch, 1 row with 44, 46, 72, 78 or 96 links, including 1 junction link;
  • (i) Roller chain of specification ANSI 41 or 410, with a pitch of 1/2 inch, 1 row with 48 links, endless, riveted;
  • (j) Single-strand roller chain of carbon steel and alloy steel of grade SAE 1010, SAE 1040 and SAE 4119, with a pitch of 0.5 inches, of specification ANSI 40 or 41, with a connecting link, uncoated;
  • (k) Roller chain of specification ANSI 50, with a pitch of 5/8 inch, 1 row with 100 links;
  • (l) Roller chain of specification ANSI 50, with a pitch of 5/8 inch, 1 row with 76 or 96 links, including 1 junction link;
  • (m) Roller chain of specification ANSI 81x, with a pitch of 1/2 inch, 1 row, with a length of 10 feet, with attachment
22 7315.12.00
  • (a) Leaf chain of carbon, alloy or stainless steel, of specification ANSI B29.8, of balanced or unbalanced construction, uncoated, zinc-flake coated or nickel plated;
  • (b) Steel bicycle chains of bushing-type (non-roller) design, of specification ISO 606, with a pitch of 12.7 mm, with an inner width of at least 2.18 mm but not exceeding 3.175 mm, for single-speed through 12-speed drivetrains;
  • (c) Chain of carbon steel, alloy steel or stainless steel of specification ISO 4948, ANSI B29.22.2001, ANSI B29.15M 1997 or ANSI B29.10M 1997, assembled, with an inner link width of at least 1 inch but not exceeding 11 inches, with a roller diameter of at least 0.906 inches but not exceeding 4.5 inches and with a pitch of at least 1.75 inches but not exceeding 18 inches, rustproofed, nickel plated, zinc plated or treated;
  • (d) Pintle chain of specification ANSI 667, with a pitch of 112 or 155, with flat bar at a centre to centre distance of 16.000 inches, with a thickness of 0.375 inches, with a height of 1 inch;
  • (e) Pintle chain of specification ANSI 88K, with a pitch of 119, with flight bars at a centre to centre distance of 22.000 inches, with a thickness of 0.375 inches, with a height of 1.25 inches high;
  • (f) Pintle chain of specification ANSI 88K, with a 2.609 inch pitch, with 138 links with flat bar, with a centre to centre distance of 24.739 inches, with a thickness of 0.5 inches, with a height of 1.25 inches;
  • (g) Special chain of specification ANSI C55, with a 1.631 inch pitch, with 1 row, with a length of 50 feet, heavy duty;
  • (h) Special welded steel chain of specification ANSI 82, with a pitch of 40, with attachment A22, with alternated attachment at a pitch of 20, non-standard, with bushed feet, heat treated
23 7315.19.00
  • (a) Connecting links, offset links and repair links of carbon, alloy or stainless steel, for use with roller chain and leaf chain, including spring clip, cottered, press-fit, single offset and double offset types, coated or uncoated;
  • (b) Parts for roller chain of carbon steel, alloy steel or stainless steel of specification ANSI B29.1, ISO 606B, BS 228 or DIN 8187, assembled, with an inner link width of at least 0.125 inches but not exceeding 1.875 inches, with a roller diameter of at least 0.130 inches but not exceeding 2.25 inches and with a pitch of at least 0.25 inches but not exceeding 4.0 inches, rustproofed, nickel plated, zinc plated or treated;
  • (c) Parts for chain of carbon steel, alloy steel or stainless steel of specification ISO 4948, ANSI B29.22.2001, ANSI B29.15M 1997 or ANSI B29.10M 1997, assembled, with an inner link width of at least 1 inch but not exceeding 11 inches, with a roller diameter of at least 0.906 inches but not exceeding 4.5 inches and with a pitch of at least 1.75 inches but not exceeding 18 inches, rustproofed, nickel plated, zinc plated or treated
  • (d) Low carbon steel or alloy steel tire chain parts, including cross chains pre-assembled with hooks, loose cross chain hooks (standard and bell-shaped), side chain end hooks, side chain fasteners and side chains with cam tightening devices, with a wire or material diameter of at least 4.5 mm but not exceeding 13 mm, clear lacquer coated
24 7315.20.00
  • (a) Low carbon steel or alloy steel complete tire chains for on-highway vehicles, including cable or wire anti-skid devices, hoop-style chains, studded chains, V-bar chains, square link chains and regular twist link chains, in single or triple configurations, with or without cam side chain tightening devices, with a wire or link diameter of at least 3.8 mm but not exceeding 17.3 mm, clear lacquer, zinc plated, bright zinc or PVC coated, for use on passenger vehicles, light trucks, SUVs, medium trucks, heavy trucks and ATVs/UTVs;
  • (b) Low carbon steel or alloy steel complete tire chains for off-highway equipment, including studded diamond pattern, H-pattern, square link, net link, multi-ring and U-grip configurations, with a wire or link diameter of at least 7 mm but not exceeding 32 mm, clear lacquer or grey paint coated, for use on agricultural, industrial, loader/grader, forklift and forestry equipment;
  • (c) Tire chains, of boron alloy steel, case hardened, with a link wire diameter of at least 7 mm but not exceeding 22 mm, fitted with side chains, cross chains, hooks and tensioning components, whether oil-finished, painted or galvanized
25 7315.81.00
  • (a) Stud link anchor chain manufactured in accordance with ISO 1704 in Grades U2, U3 or U4, of carbon steel, with a diameter of at least 0.625 inches but not exceeding 2.500 inches and a length of 90 feet, galvanized or painted;
  • (b) Stud-link anchor chains of low-alloy steel of grade CM490 Grade 2, of specification ISO 1704 and GB/T 549-2017, welded, with a link diameter of 38 mm, with a link length of 228 mm, with an inside link opening of 152 mm long and 61 mm wide, with an overall chain length of 27.5 m, black oxide finish;
  • (c) Stud-link mooring or anchor chain, of specification ISO 1704, of grade 2 or 3
26 7315.82.00 Long link studless mooring chain, of carbon steel, of specification ISO 1704, of grade U2 or U3, of a bar diameter of at least 0.375 inches but not exceeding 2.500 inches, with a length of 90 feet or 100 feet, galvanized or painted
27 7315.82.00.10
  • (a) Welded-link conveyor chain of carbon steel, of nominal size 5/8 inch, of specification ANSI CNX, with 2 cross bars and conveyor attachments, with a pitch of 203 links, bright or oiled;
  • (b) Welded-link conveyor chain of carbon steel, of nominal size 5/8 inch, of specification ANSI CNX, of break-open design, with a pitch of 254 links, bright or oiled;
  • (c) Welded-link safety chain of carbon steel, of nominal size 5/16 inch, with a length of 40 inches, with clevis attachment, galvanized;
  • (d) Welded-link conveyor chain of carbon steel, of nominal size 5/8 inch, of specification ANSI CNX, of 2-strand construction with conveyor attachments, with a pitch of 179 links, bright or oiled;
  • (e) Chain and parts thereof, of iron or non-alloy steel, welded link, of grade G20, G30, G40, G43, G50 or G63, conforming to the standard entitled NACM Welded Steel Chain Specifications;
  • (f) Low carbon steel welded link chain in regular twist link pattern, to NACM tire chain specifications, with a wire diameter of at least 7 mm but not exceeding 10 mm, clear lacquer coated, for use as tire chain cross chains or side chains
28 7315.82.00.20
  • (a) Stainless steel chains of grade 316L, of specification MIL-DTL-32655, calibrated, with a diameter of 0.19 inches, an inner length of 0.58 inches and an inner width of 0.25 inches, rated as Grade 50 with a working load limit of 1100 lbs, a minimum breaking strength of 4400 lbs, spheroidized annealed, uncoated;
  • (b) Stainless steel chains of grade 316L, of specification MIL-DTL-32655, calibrated, with a diameter of 0.28 inches, an inner length of 0.85 inches and an inner width of 0.38 inches, rated as Grade 50 with a working load limit of 2200 lbs, a minimum breaking strength of 8800 lbs, spheroidized annealed, uncoated;
  • (c) Stainless steel chains of grade 316L, of specification MIL-DTL-32655, calibrated, with a diameter of 0.39 inches, an inner length of 1.18 inches and an inner width of 0.55 inches, rated as Grade 50 with a working load limit of 4400 lbs, a minimum breaking strength of 17 600 lbs, spheroidized annealed, uncoated;
  • (d) Stainless steel chains of grade 316L, of specification MIL-DTL-32655, calibrated, with a diameter of 0.51 inches, an inner length of 1.55 inches and an inner width of 0.75 inches, rated as Grade 50 with a working load limit of 7300 lbs, a minimum breaking strength of 29 200 lbs, spheroidized annealed, uncoated;
  • (e) Stainless steel chains of grade 316L, of specification MIL-DTL-32655, calibrated, with a diameter of 0.63 inches, an inner length of 1.91 inches and an inner width of 0.90 inches, rated as Grade 50 with a working load limit of 9800 lbs, a minimum breaking strength of 39 200 lbs, spheroidized annealed, uncoated;
  • (f) Stainless steel chains of grade 316L, of specification MIL-DTL-32655, calibrated, with a diameter of 0.32 inches, an inner length of 0.95 inches and an inner width of 0.45 inches, rated as Grade 50 with a working load limit of 2700 lbs, a minimum breaking strength of 10 800 lbs, spheroidized annealed, uncoated;
  • (g) Alloy steel chains of grade 80, of specification EN 818, heat treated, quenched and tempered, spheroidized annealed, with a diameter of 0.75 inches, a length of 7 feet, link dimensions of 4.5 inches by 3 inches, ring diameter of 1 inch with a width of 8 inches across, toggle length of 12 inches and plate thickness of 0.75 inches, uncoated;
  • (h) Alloy steel chains of grade 80, of specification EN 818, heat treated, quenched and tempered, spheroidized annealed, with a chain diameter of 0.75 inches, a chain length of 7 feet, a ring diameter of 1 inch, a toggle length of 12 inches, link dimensions of 4.5 inches by 3 inches, a ring width of 8 inches across and a plate thickness of 0.75 inches, uncoated;
  • (i) Alloy steel chains of grade 80, of specification EN 818, heat treated, quenched and tempered, spheroidized annealed, with a chain diameter of 0.75 inches, an overall length of 9 feet, a ring diameter of 1 inch, a toggle length of 12 inches, link dimensions of 6.5 inches by 3.5 inches, a ring width of 10 inches across and a plate thickness of 0.75 inches, uncoated;
  • (j) Alloy steel chains of grade 80, of specification EN 818, heat treated, quenched and tempered, spheroidized annealed, with a chain diameter of 1 inch, an overall length of 7 feet, a ring diameter of 1 inch, a toggle length of 12 inches, link dimensions of 6.5 inches by 3.5 inches, a ring width of 10 inches across and a plate thickness of 0.75 inches, uncoated;
  • (k) Alloy steel chains of grade 80, of specification EN 818, heat treated, quenched and tempered, spheroidized annealed, with a chain diameter of 0.75 inches, a length of 100 feet, link dimensions of 6.5 inches by 3 inches and a ring diameter of 1 inch with a width of 8 inches across, galvanized;
  • (l) Open link (studless) anchor chains of low-alloy steel of grade CM490 Grade 2, of specification ISO 1704 and GB/T 549-2017, welded, with a link diameter of at least 28 mm but not exceeding 38 mm, with a link length of at least 168 mm but not exceeding 228 mm, with an inside link opening of at least 112 mm but not exceeding 152 mm long and at least 42 mm but not exceeding 60.8 mm wide, with an overall chain length of at least 1.14 m but not exceeding 27.5 m, black oxide finish;
  • (m) Chain and parts thereof, of iron or non-alloy steel, welded link, of grade G20, G30, G40, G43, G50 or G63, conforming to the standard entitled NACM Welded Steel Chain Specifications;
  • (n) Alloy steel welded link chain in square link pattern, with a wire diameter of at least 6 mm but not exceeding 11 mm, clear lacquer coated, for use as tire chain cross chains or side chains;
  • (o) Welded-link chain assemblies, of alloy steel, of grade 80, fitted with forged alloy steel hooks, with a chain diameter of at least 12.70 mm but not exceeding 31.75 mm, whether painted or uncoated
29 7315.89.00
  • (a) Alloy steel chain links of grade AISI 115MA or 105MA, or carbon steel chain links of specification ASTM A304, produced by investment casting (lost wax process), non-welded, as-cast or heat treated, of oval or round configuration, with a cross-sectional diameter of at least 16 mm but not exceeding 65 mm and with a length of at least 100 mm but not exceeding 400 mm;
  • (b) Sash chain of carbon steel, size 8, with a width of 0.245 inches, in rolls of 500 feet, zinc plated;
  • (c) Non-welded chains of carbon steel of grade SAE 1008, with a link length of 19 mm, with a wire diameter of 4.5 mm or 5 mm, with a rated load of at least 30.7 tonnes but not exceeding 31.4 tonnes, with a length of at least 20 feet but not exceeding 1000 feet, zinc plated;
  • (d) Carbon steel welded oval-link chain for gate closure, with a link wire diameter of 6 mm, with a chain length of at least 300 mm but not exceeding 500 mm, with connecting pin and mounting hardware, hot-dip galvanized to ASTM A153 Class C;
  • (e) Protection chains, of alloy steel or carbon steel, heat treated, of mesh construction, with a link wire diameter of at least 12 mm but not exceeding 23 mm, whether painted or uncoated
30 7315.90.00
  • (a) Carbon steel or austenitic stainless steel connectors, shackles and joining components, for use as parts of chain, produced by investment casting (lost wax process), as-cast or machined, with a cross-sectional diameter of at least 20 mm but not exceeding 75 mm, with a width of at least 75 mm but not exceeding 300 mm and with a length of at least 100 mm but not exceeding 350 mm, uncoated;
  • (b) Anchor chain swivels manufactured under IACS requirements for use with Grade U3 anchor chain manufactured in accordance with ISO 1704, of carbon steel, with a diameter of at least 28 mm but not exceeding 75 mm, painted;
  • (c) Connecting links, coupling links and master links, of alloy steel, of grade 80 or 100, painted, of standard ASME B30.9, galvanized or uncoated;
  • (d) Parts of tire chains, track chains and protection chains, of alloy steel or carbon steel, including cross chains, side chains, hooks, connectors, links, pins, bushings and fasteners, whether uncoated, oil-finished or painted
31 7317.00.00
  • (a) Nails of iron or steel, certified for steel and metal manufacturing construction, of a diameter of at least 4 mm but not exceeding 25.4 mm, coated or uncoated;
  • (b) Steel track spikes (cut spikes), of a square cross-section, with a side dimension of 0.63 inches, with a length of 6 inches, with a spike head measuring 0.31 inches by 0.31 inches by 0.69 inches, conforming to the standard entitled AREMA Manual for Railway Engineering, Chapter 5, Section 2.1.3
32 7318.11.00
  • (a) Railroad track bolts, of heat-treated carbon steel, with matching untreated carbon steel nuts, with a diameter of 1.000 inch or 1.125 inches;
  • (b) Steel screw spikes conforming to the standard entitled AREMA Manual for Railway Engineering, with a rectangular head of 15/16 inch in width
33 7318.14.00
  • (a) Deck board fastening clips, of stainless steel and nylon, each consisting of a stamped stainless steel gusset, a self-drilling stainless steel screw and an injection-moulded nylon 66 body, gusset of stainless steel of grade 304 or 305, screw of stainless steel of grade 410, with a width of 25 mm, a depth of 18 mm and a height of 51 mm, gusset and screw passivated and epoxy-coated;
  • (b) Deck board fastening clips, of stainless steel and nylon, each consisting of a stamped stainless steel gusset, a stainless steel screw and an injection-moulded nylon 66 body, gusset of stainless steel of grade 304 or 305, screw of stainless steel of grade 304 or 305, with a width of 49 mm, a depth of 18 mm and a height of 65 mm, gusset and screw passivated and epoxy-coated
34 7318.15.00
  • (a) Welded metal fasteners ("weld studs"), cold forged or hot forged, threaded or unthreaded, headed or unheaded, tapped, with or without a collar, flanged and unflanged, with a diameter of at least 2 mm but not exceeding 32 mm;
  • (b) Insulation fasteners and weld pins for HVAC ductwork and insulation installation;
  • (c) Threaded rods, of alloy steel, of specification ASTM A193 Grade B7, with a diameter of 0.75 inches, with a length of 16 inches, electro zinc-plated, supplied with nuts and washers;
  • (d) Rail bolts, of high-strength carbon steel, of Grade 5 button-head ovalneck bolt type, with a nominal diameter of 1.125 inches and a length of 6 inches measured under the head, with rolled UNC threads, conforming to the standard entitled AREMA Manual for Railway Engineering;
  • (e) Square nuts, of high-strength carbon steel, with rolled internal UNC threads, of Grade 5 nut type, conforming to the standard entitled AREMA Manual for Railway Engineering, with a thickness of at least 1.079 inches but not exceeding 1.155 inches
35 7318.15.00.42
  • (a) Armour bolts, of carbon or alloy steel, forged, hardened and tempered, with oval heads, oval collars (anti-rotation), UNC-2A threads, with a nominal diameter of at least 1.5 inches but not exceeding 2 inches, with a length under head of at least 7 inches but not exceeding 45 inches;
  • (b) Threaded hex bolts, of stainless steel, of grade 316L, of a nominal diameter of 0.375 inches or 0.5 inches, of a length of 3.25 inch, 3.5 inches or 5.5 inches, with thread pitches of 13 or 16 threads per inch
36 7318.15.00.45
  • (a) Double-ended stud, of standard M8, with thread pitch of 1.25 mm and length of 37 mm, with external 6-lobe drive and 17.5 mm header point, with acid treatment and zinc or nickel coating;
  • (b) Double ended stud, of standard M8, with a thread pitch of 1.25 mm and length of 25 mm, pan head serrated neck, of grade 10.9, with zinc coating;
  • (c) Double ended stud, of standard M6, with a thread pitch of 1 mm, of grade 10.9, with zinc coating;
  • (d) Projection weld stud of standard M8, with a length of 30 mm, with zinc coating;
  • (e) Round-interior studs, of standard M6, with a diameter of 18.75 mm, with a rod diameter of 0.305 inches, plain coating;
  • (f) Studs, of M6 standards, with a 23.75 mm head diameter, with a 1.5 mm thread pitch, with a 25 mm length, with a rod diameter of 0.345 inches;
  • (g) Studs, of M6 standard, of 18.97 mm head diameter of the stud, with a thread pitch of 1 mm, with a length of 21 mm, with a rod diameter of 0.305 inches;
  • (h) Studs, of M6 standard, with 18.97 mm head diameter, with a 1 mm thread pitch, with a length of 20 mm length, with a rod diameter of 0.305 inch
37 7318.15.00.49
  • (a) Bolts, flange head, self-tapping, of standard M10, with a thread pitch of 1.5 mm and a length of 30 mm, meeting GM6202M, with a thread-forming surface treatment;
  • (b) Socket bolts, of standard M12, with a thread pitch of 1.75 mm and a length of 120 mm, of grade 8.8, with a corrosion-protective surface treatment, meeting automotive specifications;
  • (c) Clinch pins, of steel grade SAE 10B21 or 10B22, of 6 mm diameter and 12.5 mm length, with zinc-plated coating for corrosion protection;
  • (d) Bolts, hex flange, of standard M12, with a thread pitch of 1.75 mm and a length of 80 mm, of property class 10, with a corrosion-protective aluminum-organic surface coating;
  • (e) Bolts, hex flange, of standard M12, with a length of 120 mm, of property class 10, with a corrosion-protective aluminum-organic surface coating;
  • (f) Carbon steel shoulder-type eye bolts of grade C1030/C1035, of specification ASTM A489, ANSI B18.15 and MS51937, with a Unified National Coarse (UNC) thread size of at least 1/4-20 but not exceeding 2-4 1/2, with a shank length of at least 1 inch but not exceeding 6 inches, with an eye inside diameter of at least 3/4 inch but not exceeding 3 3/8 inches, with an eye outside diameter of at least 1 3/16 inches but not exceeding 6 7/8 inches, with an overall length of at least 2 3/8 inches but not exceeding 11 7/8 inches, with a rated capacity of at least 650 lbs but not exceeding 40 000 lbs, uncoated, zinc plated or galvanized;
  • (g) Carbon steel plain-type eye bolts of grade C1030/C1035, of specification ASTM A489 and ANSI B18.15, with a UNC thread size of at least 1/4-20 but not exceeding 2-4 1/2, with a shank length of at least 1 inch but not exceeding 4 inches, with an eye inside diameter of at least 3/4 inch but not exceeding 3 3/8 inches, with an eye outside diameter of at least 1 3/16 inches but not exceeding 6 7/8 inches, with an overall length of at least 2 7/32 inches but not exceeding 11 inches, with a rated capacity of at least 650 lbs but not exceeding 40 000 lbs, uncoated or zinc plated;
  • (h) Carbon steel alloy-type eye bolts of grade C1030/C1035, of specification ASTM F541 and ANSI B18.15, with a UNC thread size of at least 3/8-16 but not exceeding 2-4 1/2, with a shank length of at least 1 1/4 inches but not exceeding 4 inches, with an eye inside diameter of at least 1 inch but not exceeding 3 1/4 inches, with an eye outside diameter of at least 1 21/32 inches but not exceeding 6 7/8 inches, with an overall length of at least 3.28 inches but not exceeding 11.88 inches, with a rated capacity of at least 1480 lbs but not exceeding 47 600 lbs, uncoated
38 7318.16.00
  • (a) Steel hex nuts and locknuts, with male or female threads, for tube fittings, of UNF thread specifications 5/8-18, 7/8-18 and 1-1/16-14;
  • (b) Clinch nuts, of zinc-plated steel
39 7318.16.00.90
  • (a) Hex nuts, of projection weld type, of specification M12, with a thread pitch of 1.25 mm, of grade 8 steel, with a bare surface and rust-inhibitor treatment;
  • (b) Weld studs, of specification M6, with a thread pitch of 1 mm, with a length of 16 mm, of specification GMW25M (8.8), with a maximum carbon content of 0.26% and plain coating;
  • (c) Studs, projection-weld, of specification M6, with a thread pitch of 1 mm, with a length of 25 mm, of specifications GMW25M;
  • (d) Studs, projection-weld, of specification M6, of 1 mm thread pitch and 20 mm length, of property class 8.8;
  • (e) Weld hex nuts, of specification M8, of 1.25 mm thread pitch, with head diameter of 22.5 mm, of 0.59 inch wire rod;
  • (f) Threaded anchor nuts, of iron or steel, with a nominal diameter of 35 mm or 46 mm
  • (g) Heavy hex nuts, of carbon steel, alloy steel or stainless steel, of grade 2H, 2HM or 7L of specification ASTM A194/ASME SA194, of grade L7 or L7M of specification ASTM A194/ASME SA194, or of grade B6, B8, B8C, B8T, B8M, 8 (304) or 8M (316) of specification ASTM A194/ASME SA194, with a diameter of at least 0.25 inches but not exceeding 4 inches, plain, trivalent zinc plated, fluoropolymer coated, hot-dip galvanized to ASTM A153 or passivated
40 7318.19.00.00 Threadbars, of steel, of grade 150, of specification ASTM A722, with a nominal diameter of 1.375 inches or 1.75 inches, with a length of 16.8 feet, 17 feet, 20.62 feet or 22.5 feet
41 7318.21.00
  • (a) Washers or retaining washers used in conjunction with "weld studs" or "weld pins", with an inside diameter of at least 1.6 mm but not exceeding 6 mm;
  • (b) Steel lock washers, of grade ASTM Grade 5 or 8, conforming to the standard entitled AREMA Manual for Railway Engineering, with a nominal size of 0.875 inches, 1.000 inch or 1.125 inches;
  • (c) Railway-grade high-strength carbon steel spring lock washers, conforming to the standard entitled AREMA Manual for Railway Engineering, of an inner diameter of at least 30 mm but not exceeding 32 mm, of an outer diameter of at least 59 mm but not exceeding 65 mm, with a nominal thickness of at least 3.6 mm but not exceeding 4.6 mm, for use with rail bolts of a nominal diameter of 29 mm;
  • (d) Carbon steel spring lock washers, conforming to the standard entitled AREMA Manual for Railway Engineering, of an inner diameter of at least 1.06 inches but not exceeding 1.13 inches, of an outer diameter of at least 2.0 inches but not exceeding 2.1 inches
42 7318.22.00.00 Non-threaded washers, of stainless steel, of grade 316L, of nominal size 0.375 inches or 0.5 inches
43 7318.29.00
  • (a) Steel collar-lock rivets, of specification ASTM F568 or ISO 898-1 Grades 8.8 and 10.9 for industrial and transportation applications, with a diameter of 0.25 inches or more, with a length of 2.38 inches or more and fitted with an alloy steel collar with a coating of specification ASTM B633;
  • (b) Retaining clips, of carbon steel, of a type used to secure hitch pins or of hinge type;
  • (c) Spring pins, of carbon steel or stainless steel, with a diameter of at least 0.8 mm but not exceeding 20 mm;
  • (d) Steel pins, of carbon steel or stainless steel, with a diameter of at least 1.5 mm but not exceeding 6.5 mm
44 7326.20.00 Wire racks, of steel, of a length of at least 9 cm but not exceeding 37 cm, of a width of at least 12 cm but not exceeding 37 cm and of a height of at least 20 cm but not exceeding 75 cm
45 7326.90.10
  • (a) Carbon steel tube thimble with incorporated forged master link, formed and bent, hot-dip galvanized, with a thimble inside diameter of 94 mm, with a thimble outside diameter of 114 mm and with a thimble length of 460 mm, with a master link diameter of 38 mm, with a master link outside length of 267 mm, with a master link outside width of 211 mm, with a master link inside length of 267 mm and with a master link inside width of 135 mm;
  • (b) Forged alloy steel shackle with screw pin, heat-treated, hot-dip galvanized and powder coated, with a lift capacity of 35 tonnes, with a body diameter of at least 51 mm but not exceeding 122 mm, with bore hole diameters of 57 mm, with a screw pin length of 188 mm, with an overall height of 340 mm, with an overall width of 249 mm, with an inside top opening of 146 mm and with an inside bottom opening of 86 mm;
  • (c) Pressure-vessel steel heads, of grade SA414-G or SA516-70, with diameters of 24 inches or 30 inches, for use as end closures in pressure vessels
46 7326.90.90
  • (a) Steel hose clamps, single-band type, of grade 51CrV4, of specification SAE J404 6150M, of a thickness of at least 0.98 mm but not exceeding 1.08 mm, with a width of 15 mm, of a nominal size of 16 mm or 17 mm, of a closed diameter of 14.9 mm or 15.6 mm, of a full-open diameter of 17.5 mm or 18.5 mm, of a clamping force of 145 mm or 195 mm, with a chrome-free zinc-based epoxy coating;
  • (b) Steel hose clamps with plastic removal clips, double-band type, of grade 51CrV4, of specification SAE J404 6150M for the band and of grade PA55 Type 6.6, of a thickness of at least 0.98 mm but not exceeding 1.08 mm, with a width of 10 mm or 15 mm, of a nominal size of 16 mm or 17 mm, with a chrome-free zinc-based epoxy coating;
  • (c) Steel spools, cold-rolled, of grade CQ1008 or CQ1010, fabricated with an eight-rib design, with flange diameters of 8 inches and 10 inches, with a drum diameter of 4.5 inches, with a traverse length of 6 inches, with an arbor size of 1.25 inches, painted;
  • (d) Forged steel saw-blade blanks, with coating;
  • (e) Breakaway couplings, machined from round ETD 4142 alloy-steel bar stock, hot-wrought to a specification ASTM A29/A29M-20, galvanized after machining to ASTM A153 and packaged with hardware galvanized to ASTM A653;
  • (f) Breakaway couplings, of alloy steel, hot-wrought, of grade ETD 4142, galvanized to ASTM A513, with hardware;
  • (g) Female anchoring systems for concrete, comprising a pinch-welded assembly of a stainless steel washer of grade 304, a steel coil of grade 1080 with a diameter of 0.4375 inches, a stainless steel internally threaded ferrule of grade 304 with a Unified National Coarse (UNC) thread size of 0.625 inches nominal diameter and 11 threads per inch, and a carbon steel rod of grade 1045 with a diameter of 0.4375 inches;
  • (h) Steel hinge assemblies, with hinge plates of grade 4140/42, galvanized to ASTM A153, and supplied with galvanized attachment hardware;
  • (i) Laboratory spatulas, of stainless steel, of specification ASTM F899-84
47 7326.90.90.30 Hangers and similar supports, of iron or steel, for tubes and pipes
48 7326.90.90.90
  • (a) Shackles of alloy steel, closed-die forged and quenched and tempered, with a diameter range of 0.1875 inches to 2.500 inches, covering standard and wide opening mooring shackles, galvanized, manufactured in accordance with RR-C-271D, Type IVA, Grade A, Class 2, ASME B30.26, high tensile steel, forged-quenched and tempered, Grade 6;
  • (b) Pear-shaped connecting links of alloy steel, with a diameter of at least 25 mm but not exceeding 40 mm, painted, manufactured in accordance with RR-C-271F;
  • (c) Eye and eye swivels of alloy steel, with a diameter of at least 0.375 inches but not exceeding 1.500 inches, galvanized. Forged-quenched and tempered. Manufactured in accordance with RR-C-271F, Type VII, Class 2;
  • (d) Thimbles of alloy steel, with a diameter of at least 0.25 inches but not exceeding 2.250 inches, galvanized, manufactured in accordance with FF-T-276C;
  • (e) Tube thimbles with integrated master link of alloy steel, with a tube diameter of at least 65 mm but not exceeding 105 mm and an integrated master link diameter of at least 28 mm but not exceeding 36 mm, galvanized, manufactured in accordance with FF-T-276C;
  • (f) Steel horseshoes of grade ASTM A36 or AISI 1018, forged, with a thickness of at least 6.5 mm but not exceeding 13 mm, with a width of at least 15 mm but not exceeding 33 mm and with a heel-to-heel circumference of at least 175 mm but not exceeding 600 mm, uncoated;
  • (g) Mild steel plates of specification ASTM A36, cold drawn, with a height of 22 mm or 26 mm, with a width of 48 mm, with a length of 46.75 inches and with three 8 mm diameter holes, with an outer PVC tube;
  • (h) Mild steel bars of specification ASTM A36, cold drawn, with a height of 22 mm, with a width of 38 mm, with a length of 20.75 inches, 22.25 inches or 23.75 inches and with two 12 mm diameter holes, PVC coated;
  • (i) Cast iron ballast ingots of specification ASTM A48, cast, with a height of 42 mm, with a width of 44 mm and with a length of 207 mm, polyethylene powder coated;
  • (j) Steel turnbuckle assemblies of grade AISI 1045, of specification ASTM A668 Grade D or Grade F, assembled, quenched and tempered, with a diameter of at least 3 inches but not exceeding 4 inches and with a length of 39 inches, zinc coated;
  • (k) Tubular sleeves of cold-rolled non-alloy steel of grade DC01 +C690, of specification EN 10139, work-hardened, with a tensile strength of at least 690 MPa, with a diameter of at least 21 mm but not exceeding 24 mm, with a length of at least 1200 mm but not exceeding 1370 mm and with a wall thickness of at least 0.71 mm but not exceeding 0.86 mm, polypropylene coated;
  • (l) Low alloy steel cast rigging components for forestry applications, of grade 80-50, of specification ASTM A148, cast, spheroidized annealed, with a width of 0.75 inches, with a length of 6 inches and with a diameter of 1 inch, painted;
  • (m) Low alloy steel cast and welded rigging components for forestry applications, of grade 80-50, of specification ASTM A148, cast and welded, spheroidized annealed, with a width of 0.625 inches and with a length of 6 inches, painted;
  • (n) Cold-forged stainless steel conveyor belt fasteners of grade 316 with stainless steel or carbon steel staples, with or without polyurethane foam molded in loop area, for belts with a thickness of at least 5 mm but not exceeding 20 mm and with a belt strength not exceeding 4000 kN/m;
  • (o) Stainless steel ceiling support (flange) for electrical conduits, uncoated;
  • (p) Galvanized steel ratchets for garage door tensioners, in left or right orientation, with slotted spring pin of black oxide finished steel;
  • (q) Steel shaft collars, with an inside diameter of 1 inch, with an outside diameter of 1.485 inches, with a width of 0.495 inches, with 1 or 2 set screws of 5/16 inch thread (screws not included), zinc plated;
  • (r) Steel threaded shaft clamp, with dimensions of 2.031 inches by 1.986 inches by 0.236 inches, zinc plated;
  • (s) U-shaped steel ceiling rail bracket of grade Q235, with 5/16-18 conduit mounting screw, zinc plated;
  • (t) Forged carbon steel or alloy steel pin coupler shackles and rated screw pin anchor shackles, with a nominal size of at least 8 mm but not exceeding 22 mm, clear lacquer or hot-dip galvanized coated, for use as tire chain connecting hardware;
  • (u) Forged alloy steel forestry track bar profiles, track locks, and replacement studs, with studs of at least 20 mm but not exceeding 30 mm thickness, grey paint or clear lacquer coated, for use as traction and tire protection systems on forestry equipment;
  • (v) Welded metal fasteners ("weld studs"), of mild or stainless steel, cold forged, hot forged, threaded or unthreaded, headed or un-headed, tapped, with or without a collar, flanged or unflanged, with a diameter of at least 2 mm but not exceeding 32 mm;
  • (w) Step assemblies, of steel, with standard drive operation and power switch kit, with a step extension of 25.5 inches, with a load capacity of 300 pounds;
  • (x) Stainless-steel cylindrical shell, of 10-gauge SA240-304 stainless-steel plate, with an outer diameter of 38 inches, with a length of 82 inches, with an 2B interior finish and a 180-grit exterior finish, welded on two sides, wrapped in polyvinyl chloride on two sides;
  • (y) Steel anchor heads for post-tensioning, of specification EN ISO 683-1 or EN ISO 683-2, for strand sizes 19-0.6, 27-0.6 and 31-0.6, for intermediate grouting, comprising galvanized multi-port anchors with two 0.75-inch National Pipe Taper (NPT) ports and associated anchoring and grouting components;
  • (z) Grout caps for use with strand sizes 19-0.6, 27-0.6, 31-0.6, 1.375 inches and 1.75 inches, of specification EN 10130, with stainless steel pipe fittings and ball valves;
  • (z.1) Three-piece wedges of iron or steel, of specification EN 10277, with a nominal diameter of 0.62 inches;
  • (z.2) Couplings, of type ASTM C1277 or CSA B602, with a neoprene sleeve and stainless steel shield and clamps, of a diameter of at least 1.5 inches but not exceeding 15 inches
49 8302.41.90
  • (a) Steel counterbalancing system support with 3/8 inch cable, left orientation, zinc plated;
  • (b) Steel T-handle flush-mount locking bolt for garage doors, with a length of 3 1/4 inches;
  • (c) Steel garage door emergency release plunger assembly, consisting of steel housing, press steel ball bearing, steel spacer and plunger spring, zinc plated;
  • (d) Cast steel garage door endlock, zinc plated;
  • (e) Steel garage door spreader bar with press steel ball bearing, with dimensions of 3.38 inches by 12.5 inches, zinc plated;
  • (f) Steel garage door rollers with nylon roller head, with a precision ball bearing (6200, 6201 or 6203 series), with a roller head diameter of at least 1.7 inches but not exceeding 3 inches, with a steel stem diameter of 0.43 inches and with a stem length of at least 4 inches but not exceeding 9 inches, zinc plated;
  • (g) Cast iron and carbon steel decorative gate and door hardware fittings, including spring door handles, pull handles, gate handles, door knockers and door studs, with a length of at least 20 mm but not exceeding 229 mm, black powder coated;
  • (h) Carbon steel spring-loaded self-closing gate closure hardware assemblies, with compression spring mechanism, in single drive and double drive configurations, with mounting hardware, with a bolt diameter of at least 12.7 mm but not exceeding 19.1 mm, hot-dip galvanized to ASTM A153, black powder coated, zinc electroplated, or electro-zinc plated with black topcoat
50 8302.41.90.20 Window hardware
51 8302.41.90.31
  • (a) Steel spring repair block with 2 set screws, with dimensions of 1.5 inches by 1.83 inches, with set screws of 3/8-16 by 1 inch, zinc plated with painted heads;
  • (b) Cast steel chain hoist support brackets, with dimensions of at least 3.54 inches by 2.72 inches but not exceeding 3.54 inches by 2.77 inches, zinc plated;
  • (c) Steel door stop block (flat bar), with dimensions of 1 inch by 6.25 inches by 0.225 inches, uncoated;
  • (d) Steel retaining spring assemblies, in left, right or universal orientation, with retractable steel rod, spring and rubber cushion, zinc plated;
  • (e) Steel spring-loaded retaining assemblies, in left or right orientation, consisting of a steel mounting bracket, sliding steel tube, extension spring, steel washer and rivet, with rubber cushion contact pad, zinc plated;
  • (f) Steel spring-loaded retaining assembly for garage doors, consisting of a steel mounting bracket, sliding steel tube, extension spring, steel washer and rivet, with rubber cushion contact pad, zinc plated;
  • (g) Stamped steel decorative garage door handle, with dimensions of 11.2 inches by 1.58 inches, black painted;
  • (h) Cast steel blade tip endlocks for rolling doors, with or without rivets, with dimensions of approximately 1.5 inches by 2 inches by 0.5 inches, zinc plated;
  • (i) Steel retaining spring leaf kits, consisting of 2 L-shaped steel supports of 9 inches by 1.250 inches by 0.375 inches (zinc plated), 2 curved spring steel leaves of 20 inches by 2 inches by 0.130 inches (black painted) and 8 bolt/nut sets (zinc plated);
  • (j) Steel auto latch assembly for garage doors, consisting of 2 steel supports and torsion spring, with overall dimensions of 2 inches by 3.75 inches by 2 inches, zinc plated;
  • (k) Stamped steel decorative garage door plate, with dimensions of 18 inches by 2 inches by 0.25 inches, with three mounting holes, zinc plated and black powder coated;
  • (l) Steel garage door rollers with stamped steel roller head and steel bearing, with a roller head diameter of at least 1.7 inches but not exceeding 3 inches, with a steel stem diameter of at least 0.43 inches but not exceeding 0.472 inches and with a stem length of at least 3.3 inches but not exceeding 9.5 inches, zinc plated or uncoated;
  • (m) Steel garage door roller with nylon roller head, with a 6200 series steel ball bearing, with a roller head diameter of 1.8 inches, with a steel stem diameter of 0.43 inches and with a stem length of 7 inches, zinc plated
52 8302.41.90.39 Door hardware, other than for garage doors
53 8302.41.90.41 Poles, rods or track
54 8302.41.90.49 Drapery accessories
55 8302.41.90.90
  • (a) Duplex stainless steel frameless glass panel brackets and clamps of grade 2205, precision cast (investment cast), including deck-mounted base brackets, inline clamps, wall-to-glass brackets, 90-degree corner clamps and adjustable clamps, compatible with a glass thickness of 12 mm, with a length of at least 25.4 mm but not exceeding 104 mm, with a width of at least 25 mm but not exceeding 104 mm and with a height of at least 65.5 mm but not exceeding 184.8 mm, matte black powder coated or satin finished;
  • (b) Mountings, fittings and similar articles, suitable for buildings other than window hardware, door hardware or drapery accessories
56 9401.71.10 Upholstered reclining seats with steel frames of grade S355, of specification EN 10025-2, formed, CNC machined and welded, with a height of at least 95 cm but not exceeding 110 cm, with a width of at least 70 cm but not exceeding 90 cm, with a depth of at least 70 cm but not exceeding 85 cm and with a frame thickness of at least 2.5 mm but not exceeding 8 mm, zinc plated, electrophoretically coated or powder coated
57 9401.71.10.10
  • (a) Upholstered infant and children’s dining chairs incorporating cold-rolled steel tubing of grade SPCC, with round tubing of an outer diameter of at least 15.88 mm but not exceeding 31.75 mm, with oval tubing of cross-sectional dimensions of at least 21.56 mm by 35.00 mm but not exceeding 30.06 mm by 44.78 mm, with a wall thickness of at least 0.8 mm but not exceeding 1.5 mm, with component lengths of at least 259.8 mm but not exceeding 1503 mm, powder coated;
  • (b) Upholstered chaise or convertible sofas with steel tubular frames, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated;
  • (c) Upholstered reclining chairs for domestic purposes, with cold-formed welded steel tube frames of grade E235+CR1-KV of specification EN 10305-3, bent and welded, with a tensile strength of at least 230 MPa but not exceeding 500 MPa, with manual push-back or electrically operated reclining mechanism, uncoated or powder coated;
  • (d) Upholstered chairs, other than those with steel frames
58 9401.71.10.90
  • (a) Upholstered height-adjustable office chairs on casters, with steel tubular frames and steel bases, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch;
  • (b) Upholstered reclining sofas, loveseats and sectionals for domestic purposes, with cold-formed welded steel tube frames of grade E235+CR1-KV of specification EN 10305-3, bent and welded, with a tensile strength of at least 230 MPa but not exceeding 500 MPa, uncoated or powder coated;
  • (c) Upholstered seats, other than chairs with metal frames for domestic purposes
59 9401.71.90
  • (a) Upholstered height-adjustable office chairs on casters, with steel tubular frames and steel bases, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch;
  • (b) Upholstered office chairs for residential use, with cold-formed welded steel tube frames of grade E235+CR1-KV of specification EN 10305-3, bent and welded, with a tensile strength of at least 230 MPa but not exceeding 500 MPa, with component lengths not exceeding 90 inches, uncoated or powder coated;
  • (c) Upholstered seats, not for domestic use, with metal frames other than steel
60 9401.79.10 Seats for domestic purposes
61 9401.79.90 Seats with metal frames, non-upholstered, not for domestic purposes
62 9403.10.00.91 Desks
63 9403.10.00.92 Tables, excluding tracing tables
64 9403.10.00.99 Metal furniture of a kind used in offices, other than filing cabinets, desks or tables
65 9403.99.00 Furniture parts
66 9405.99.00 Parts of luminaires and lighting fittings
67 9406.90.11 Silos for storing ensilage, unassembled or incomplete, of glass fibre reinforced plastics, for use in the manufacture of silos
68 9406.90.19 Silos for storing ensilage, excluding those of steel
69 9406.90.20 Air-supported buildings
70 9406.90.90.10 Prefabricated buildings, of aluminum
71 9406.90.90.90 Prefabricated buildings, excluding those of steel or with a steel frame

SCHEDULE 2

(Section 3 and paragraph 5(b))

Goods
Item

Column 1

Tariff Classification Number

Column 2

Good

Column 3

Date
1 7312.10.00.22 Non-alloy steel prestressed strand composed of seven helically wound wires, including six outer wires laid over a single central core wire, low-relaxation, of grade 270, of specification ASTM A416/A416M, with an ultimate tensile strength of 1860 MPa, with a diameter of at least 9 mm but not exceeding 18 mm, uncoated March 31, 2027
2 7317.00.00 7326.20.00 Steel fibres bundled into strips by means of a water-soluble binder, of specification ASTM A820, EN 14889-1 or ISO 13270 Class A, with cross-sectional dimensions of at least 0.75 mm but not exceeding 0.90 mm, with a nominal tensile strength of 2200 MPa, bright March 31, 2027
3 7326.11.00 (a) Semi-autogenous grinding balls for mills, of steel containing 0.6% carbon, forged or stamped, with a diameter of 5 inches; (b) Grinding balls for mills, of steel, forged or stamped, heat-treated, with a diameter of 3.5 inches Day on which this Schedule comes into force

SCHEDULE 3

(Section 3 and paragraph 5(c))

Goods
Item

Column 1

Business Number

Column 2

Tariff Classification Number

Column 3

Goods

Column 4

Period

Column 5

Condition
1 101801561RM0001 7312.10.00.33 Alloy steel and carbon steel 8-strand plasticated wire rope of wire grade C82D of specification EN ISO 16120-2, of rope grade 1960 of specification EN 12385-4, quenched and tempered, with swaged ferrule end fittings and pulling loops, with a minimum tensile strength of 1770 MPa, with a rope diameter of at least 64 mm but not exceeding 70 mm, with a total length of at least 49.54 m but not exceeding 116.02 m, plastic impregnated    
2 102145075RM0001 7318.14.00
  • (a) Deck board fastening clips, of stainless steel and nylon, each consisting of a stamped stainless steel gusset, a self-drilling stainless steel screw and an injection-moulded nylon 66 body; gusset of stainless steel of grade 304 or 305; screw of stainless steel of grade 410; with a width of 25 mm, a depth of 18 mm and a height of 51 mm; gusset and screw passivated and epoxy-coated;
  • (b) Deck board fastening clips, of stainless steel and nylon, each consisting of a stamped stainless steel gusset, a stainless steel screw and an injection-moulded nylon 66 body; gusset of stainless steel of grade 304 or 305; screw of stainless steel of grade 304 or 305; with a width of 49 mm, a depth of 18 mm and a height of 65 mm; gusset and screw passivated and epoxy-coated
 From December 26, 2025 to December 31, 2028  
3
  • 103219127RM0001
  • 105627269RM0001
  • 742677412RM0001
  • 768597536RM0002
  • 772824660RM0001
  • 796552800RM0001
  • 807483052RM0001
  • 807558622RM0001
  • 812478899RM0001
  • 815431630RM0001
  • 837438464RM0001
  • 841203946RM0001
  • 850674235RM0001
  • 862293776RM0001
  • 865611263RM0001
  • 867804759RM0001
  • 871822474RM0001
  • 873361117RM0001
  • 899692719RM0001
 7308.30.00.29 Door frames, of iron or steel, for commercial greenhouses From December 26, 2025 to May 31, 2027  
7308.90.00.99 Formed plate sections, gutter end stops and fabricated brackets and consoles, of iron or steel, for commercial greenhouses From December 26, 2025 to May 31, 2027
7312.10.00.31 Ropes and cables of stainless steel, not electrically insulated, of 7x7 construction, with a diameter of 3 mm, for commercial greenhouse screen systems From December 26, 2025 to May 31, 2027
7315.82.00.10 Chain of iron or non-alloy steel, welded link, hot-dip galvanized, for suspending commercial greenhouse distribution piping From December 26, 2025 to May 31, 2027
7318.13.00 Screw hooks and screw rings, of iron or steel, for commercial greenhouses From December 26, 2025 to May 31, 2027  
7318.14.00 Self-tapping screws, of iron or steel, for commercial greenhouses From December 26, 2025 to May 31, 2027
7318.15.00 Bolts and screws, of stainless steel or zinc-coated steel, for commercial greenhouses From December 26, 2025 to May 31, 2027  
7318.16.00 Nuts, of stainless steel or of zinc-coated steel, for commercial greenhouses From December 26, 2025 to May 31, 2027  
7318.21.00 Spring washers and other lock washers, of iron or steel, for commercial greenhouses From December 26, 2025 to May 31, 2027  
7318.22.00 Other washers, of iron or steel, for commercial greenhouses From December 26, 2025 to May 31, 2027  
7318.29.00 Non-threaded pins and fasteners, of iron or steel, for commercial greenhouses From December 26, 2025 to May 31, 2027  
7320.20.00.90 Helical springs, of iron or steel, for commercial greenhouse glazing and screen systems From December 26, 2025 to May 31, 2027  
7326.90.90.90 Formed clips, retaining fingers, coupler pins and guide brackets, of iron or steel, for commercial greenhouse screen and ventilation systems From December 26, 2025 to May 31, 2027  
9406.90.90.90 Unassembled multi-span glass-covered commercial greenhouses with a load-bearing steel frame, an aluminum roof glazing system, aluminum ventilation windows and glazing of glass of a thickness of 4 mm From December 26, 2025 to May 31, 2027  
4 704772029RM0001 7308.20.00 Wind towers and sections of those towers From March 1, 2027 to October 31, 2027 Imported to fulfill contract for PO 981398
7308.20.00 Wind towers and sections of those towers From January 1, 2028 to December 31, 2028 Imported for sale to company with business number 731986352 RC0001
7308.20.00 Wind towers and sections of those towers From January 1, 2028 to December 31, 2028 Imported for sale to company with business number 732770953 NS0001
5 726995095RM0001 7308.20.00 Transmission towers and sections of those towers From July 1, 2026 to December 31, 2026 Imported for sale to company with business number 785951369NS0001
6 759896830 9406.20.00.00 Prefabricated modular building units, of steel, comprising galvanized structural framing members including columns, tie beams, bracing and roof trusses, integrated wall, gable and corner wall panels, and steel roofing and cladding, of grade Q235B of specification GB/T 700, finished with a polyvinylidene fluoride paint coating From December 26, 2025 to May 31, 2027  
7 785498411 7308.90.00.99 Steel frame skids of grade 50, of specification ASTM A572/A572M-21 or ASTM A992, hot-rolled, fabricated from wide flange sections and formed plate, with a width of 8 feet, with a length of at least 8 feet but not exceeding 40 feet and with a height of 6 inches, uncoated    
8 830826913 7318.12.00 Structural wood screws with self-tapping tip, of carbon steel of material number 1.5505 or 1.5506 of specification EN 10263-4:2001, or of stainless steel of material number 1.4567 of specification EN 10088-3:2005 or EN 10263-5:2001, case-hardened, with a diameter of at least 6 mm but not exceeding 14 mm, with a length of at least 60 mm but not exceeding 1500 mm, electroplated with a coating thickness of at least 8 microns but not exceeding 15 microns From December 26, 2025 to March 31, 2027  
9 832117378 7318.14.00 (a) Stainless steel wedge clips and edge clips of grade 304, pre-assembled with stainless steel gussets and nylon spacers, with self-tapping screws of a diameter of 0.117 inches, with a length of at least 1.75 inches but not exceeding 2.25 inches, with trim head T15 drive; (b) Carbon steel or stainless steel (grade 304) self-tapping screws with dual reversing pitch threads, chisel point tips and trim head T15 drive, with a diameter of 0.116 inches and with a length of 2.341 inches, loose or collated in plastic strips From December 26, 2025 to December 31, 2028  
10 847377041RM0001 7308.90.00.20
  • (a) Structural roofing panel;
  • (b) Metal closures
   Imported to fulfill contract for 20-B-77465
7308.90.00.99 Structural steel beams, steel angles, wall panels or trim   Imported to fulfill contract for 20-B-77465
7318.14.00 Screws, bolts, nuts or coach screws   Imported to fulfill contract for 20-B-77465
7318.15.00.42 Bolts   Imported to fulfill contract for 20-B-77465
7318.16.00.10 Nuts   Imported to fulfill contract for 20-B-77465
7318.21.00 Washers   Imported to fulfill contract for 20-B-77465
7318.23.00 Rivets   Imported to fulfill contract for 20-B-77465
7326.90.90.90 Clips   Imported to fulfill contract for 20-B-77465
11 867979973RT0001 9401.71.10.10
  • (a) Upholstered single-seat lounge chairs with or without arm rests, with steel tubular frames, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated;
  • (b) Upholstered ottomans with steel tubular frames, with a wall thickness not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated;
  • (c) Upholstered single seats without backrests, with steel tubular frames, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated;
  • (d) Upholstered multi-seat chairs with backrests and arm rests, with steel tubular frames, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch;
  • (e) Upholstered bar-height chairs with or without backrests and arm rests, with steel tubular frames, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated;
  • (f) Upholstered lounge-height chairs with or without backrests and arm rests, with steel tubular frames, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, with an outer diameter of at least 0.5 inches but not exceeding 1 inch, plated
    
9401.71.10.90 Steel tubular frames for office chairs, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, an outer diameter of at least 0.5 inches but not exceeding 1 inch, height adjustable, painted    
9401.71.90 Steel tubular frames for office chairs, with a wall thickness of at least 0.1 inches but not exceeding 0.8 inches, an outer diameter of at least 0.5 inches but not exceeding 1 inch, painted    
12 871571907RM0001 7308.90.00.70 Columns, pillars, posts, beams, girders and similar structural units, of steel From December 26, 2025 to March 31, 2029  
7326.90.90 Other articles of iron or steel From December 26, 2025 to March 31, 2029  
13 884309220RM0001 7318.12.00
  • (a) Carbon steel, heat-treated, self-tapping structural wood screws, partially threaded, countersunk head, washer head, flat head with shoulder or hex head, Torx or hex drive, self-tapping or self-drilling point, with a nominal diameter of at least 3 mm but not exceeding 16 mm, with a length of at least 16 mm but not exceeding 1000 mm, electrolytic zinc coating with chromate or thick-film passivation, with a salt spray resistance of at least 96 hours per ISO 9227, for use in structural wood-to-wood connections in construction;
  • (b) Carbon steel, heat-treated, self-tapping structural wood screws, fully threaded, cylindrical head, countersunk head, hexagonal star head or reverse star head, Torx or hex drive, self-drilling point, with a nominal diameter of at least 5 mm but not exceeding 14 mm, with a length of at least 70 mm but not exceeding 1500 mm, electrolytic zinc coating with chromate or thick-film passivation, or zinc-nickel alloy coating, with a salt spray resistance of at least 96 hours per ISO 9227, for use in structural wood-to-wood connections in construction;
  • (c) Low-carbon steel, heat-treated, self-tapping structural wood screws, partially threaded, hex washer head, Type 17 drill point, with a nominal diameter of 6.35 mm (1/4 inch), with a length of at least 38 mm but not exceeding 203.2 mm, with a corrosion-resistant coating equivalent to hot-dip galvanization per ASTM A153, Class D, for use in wood-to-wood and steel-to-wood structural connections in construction
 From December 26, 2025 to March 31,2027  
14 887103554RM0001 7312.10.00 Galvanized steel wire rope of grade Extra Improved Plow Steel (EIPS), of specification EN 12385-4, processed by stranding in 6x26 Warrington Seale construction, with independent wire rope core and right-hand regular lay, with a diameter of 2 inches (50.8 mm) and with a length of 2600 feet (793 metres), lubricated From December 26, 2025 to December 31, 2028 Imported to fulfill contract GSCM25001
15 891165441RM0002 7308.90.00.60 Storage racking systems, platforms and towers, including parts, but excluding wire mesh decking, of iron or steel, with vertical load-bearing members that are at least 50 mm wide, assembled to any extent or unassembled From December 26, 2025 to March 31, 2029 Imported for sale to company with business number 871571907RM0001
7308.90.00.70 Columns, pillars, posts, beams, girders and similar structural units, of steel From December 26, 2025 to March 31, 2029 Imported for sale to company with business number 871571907RM0001
7308.90.00.99 Structural supports, mesh gangways, stairs for recovery boiler From December 26, 2025 to March 31, 2029 Imported for sale to company with business number 871571907RM0001
7326.90.90 Other articles of iron or steel From December 26, 2025 to March 31, 2029 Imported for sale to company with business number 871571907RM0001
7326.90.90.90 Support for piping From December 26, 2025 to March 31, 2029 Imported for sale to company with business number 871571907RM0001
16 7308.20.00 Transmission towers and sections of those towers From November 1, 2026 to March 1, 2027 Imported for sale to company with business number 121454151RT0001 to fulfill procurement process RFP21004

REGULATORY IMPACT ANALYSIS STATEMENT

(This statement is not part of the Order.)

Issues

The Government of Canada imposed a 25% surtax on certain steel derivative products, effective December 26, 2025, and announced that requests for remission of tariffs on these products would be considered on a case-by-case basis to address situations where goods cannot be sourced domestically or other exceptional circumstances that could have severe adverse impacts on the Canadian economy.

Background

In June 2025, the United States (U.S.) imposed a 50% global tariff on steel derivative products, pursuant to Section 232 of the Trade Expansion Act of 1962, up from 25% that had been applied since March 2025. In August 2025, the United States also expanded the scope of products subject to the steel derivative tariff. Moreover, due to these restrictive trade measures, countries from around the world are seeking alternative export markets for their derivative steel products. Canada is uniquely exposed to this trade diversion risk given the integration of Canada-U.S. steel markets. This trade diversion is occurring in a context of global excess capacity in the steel industry, which negatively impacts both primary steel and steel derivative producers. Imports of steel derivatives, often made from primary steel produced under non-market conditions, compete with Canadian-made steel derivative products and depress demand for domestically produced steel.

The Government of Canada imposed a 25% surtax on the full value of certain imported steel derivative products from all countries, effective December 26, 2025. This measure was implemented through the Steel Derivative Goods Surtax Order and was introduced in response to concerns of trade diversion and unfair trade practices and to support domestic industries.

When the Government announced details of the surtax, it also announced that requests for remission of tariffs on derivative products would be considered on a case-by-case basis to address situations where goods cannot be sourced domestically or in other exceptional circumstances that could have severe adverse impacts on the Canadian economy. Section 115 of the Customs Tariff provides the authority for the Governor in Council to remit surtaxes on the recommendation of the Minister of Finance.

On February 24, 2026, the Steel Derivative Surtax Remission Order came into force, which provides broad remission relief to address situations where goods could not be sourced domestically or other exceptional circumstances that could have severe adverse impacts on the Canadian economy. Remission was also extended to goods imported by or on behalf of the Canadian public health, health care, public safety or national security entities listed in the Order. Remission of surtaxes was also granted for wind towers, for which a supply order was signed before December 26, 2025 (i.e. before the surtax came into force), as well as for wind towers imported into Canada for installation in an offshore wind project.

Objective

The objective of the Order Amending the Steel Derivative Surtax Remission Order, No. 1 is to provide additional relief from surtaxes for goods found to be in short supply, for specific companies that cannot avoid applicable surtaxes due to existing contractual obligations, or that are facing exceptional circumstances that could have significant adverse impacts on the Canadian economy.

Description

Pursuant to section 115 of the Customs Tariff, this Order provides additional relief from surtaxes under the Steel Derivative Goods Surtax Order. Remission is provided for surtaxes paid or payable on imports of certain goods, as set out in the Order.

The Steel Derivative Goods Surtax Remission Order is amended to extend relief from surtaxes to the following goods:

Regulatory development

Consultation

This remission Order has been made in response to remission requests received. Officials have engaged directly with requesters to assess requests received in line with the remission framework.

Canadian producers were consulted on supply conditions in Canada in respect of the goods claimed to be in short supply by remission requesters. A list of goods that had been identified in requests was published on the Department of Finance website and circulated to Canadian producers. Canadian producers were provided an opportunity to notify Finance officials whether goods were available domestically. The views of domestic producers informed the short supply determinations made with respect to goods in Schedules 1 and 2.

Indigenous engagement, consultation and modern treaty obligations

Following the completion of the assessment of modern treaty implications, no adverse impacts on potential or established Indigenous or treaty rights, which are recognized and affirmed in section 35 of the Constitution Act, 1982, were identified in the Order.

Instrument choice

Section 115 of the Customs Tariff provides the authority for the Governor in Council to remit surtaxes on the recommendation of the Minister of Finance.

Regulatory analysis

Benefits and costs

This is a relieving mechanism to the benefit of Canadian industries and entities impacted by the steel derivative surtax. Remission for goods set out in this Order will provide surtax relief to Canadian businesses that rely on imports of these products to support their operations in Canada. In the absence of remission, Canadian businesses that use these goods would have to pay for the surtax and these costs could ultimately be passed on to Canadian consumers or downstream producers.

Goods listed in Schedules 1 and 2 are goods that have been determined not to be currently produced domestically. In the absence of remission, Canadian businesses that use these goods would have to pay the surtax, which would increase business costs. Depending on the product, these costs could ultimately be passed on to Canadian consumers. Schedules 1 and 2 mitigate this issue by providing remission for such goods, regardless of the importer or the company using them.

Goods listed in Schedule 3 have been identified as those pertaining to specific companies facing exceptional circumstances, such as those with pre-existing contractual obligations. For example, companies generally require more time to complete the process of switching suppliers to avoid significant adverse impacts on the Canadian economy. In these cases, remission allows additional time for companies to fulfill original contracts or transitions to alternative suppliers without being unduly burdened by surtaxes.

In some cases, additional costs could risk the economic feasibility or significantly delay projects that otherwise would be beneficial to Canada.

The administrative costs for Canadian businesses to claim remission of the surtax are expected to be limited. In regard to requesting a refund (i.e. for goods already imported prior to the entry into force of this Order), importers would submit forms to the Canada Border Services Agency (CBSA) requesting refunds for the surtax paid on importations, accompanied by supporting documentation establishing that imported goods qualify for remission. As in all cases, the importer must also maintain records supporting their importation (e.g. related to tariff classification, entitlement to a tariff preference, and entitlement to the remission). The administrative burden would be limited, as individual businesses are expected to only make a few refund claims each covering past transactions. Therefore, the administrative cost to the CBSA is also expected to be limited.

Small business lens

Analysis under the small business lens concluded that the Order will impact small businesses. Some of the importers meet the definition of “small business” in the Policy on Limiting Regulatory Burden on Business, and the process to claim remission of duties meets the definition of “administrative burden” set out in the Policy. No additional flexibility is necessary for small businesses claiming remission, as all eligible importers already possess the original customs forms required to justify remission and will benefit from the remitted funds.

One-for-one rule

This Order relates to tax administration and is exempt from the requirement to offset administrative burden and regulatory titles under the one-for-one rule. The requirement for Canadian importers to submit claims for remission meets the Red Tape Reduction Act definition of administrative burden on businesses. However, duties are considered to be “taxes” for the purpose of the one-for-one rule and have been exempted from the offset requirement.

Effects on the environment

In accordance with the Cabinet Directive on Strategic Environmental and Economic Assessment (SEEA Directive), a preliminary scan concluded that a strategic environmental and economic assessment is not required.

Gender-based analysis plus

No impacts based on gender and other identity factors have been identified for this Order.

Implementation, compliance and enforcement, and service standards

The CBSA will assess any requests for remission made pursuant to the Order and will ensure compliance with its terms and conditions in the normal course of its administration of customs and tariff-related legislation and regulations. In doing so, the existing administrative framework will be leveraged to ensure that the costs can be managed within existing resources. Any refund issued pursuant to the Order will be administered by the CBSA. Depending on the volumes and complexity of refund submissions, the CBSA strives to achieve a 90-day processing standard.

The Government continues to review requests for remission of the surtax on steel derivative goods on an ongoing basis. In addition, the Government continues to review the Steel Derivative Surtax Remission Order to ensure that it is aligned with Canada’s evolving market circumstances. As warranted, further amendments may be made to the scope of the surtax remission.

Contact

Alan Ho
Director
Strategic Issues
International Trade Policy Division
Department of Finance
Ottawa, Ontario
K1A 0G5
Email: remissions-trq-derivatives-remises-ct-produitsderives@fin.gc.ca