Government of Canada
Symbol of the Government of Canada


Vol. 137, No. 1 — January 4, 2003

GOVERNMENT NOTICES

DEPARTMENT OF THE ENVIRONMENT

CANADIAN ENVIRONMENTAL PROTECTION ACT, 1999

Notice is hereby given that, pursuant to the provisions of Part 7, Division 3 of the Canadian Environmental Protection Act, 1999, the conditions of Permit No. 4543-2-03292 are amended as follows:

9. Total Quantity to Be Disposed: Not to exceed 90 000 m3.

A. MENTZELOPOULOS

Environmental Protection

Pacific and Yukon Region

[1-1-o]

DEPARTMENT OF THE ENVIRONMENT

CANADIAN ENVIRONMENTAL PROTECTION ACT, 1999

Notice is hereby given that, pursuant to the provisions of Part 7, Division 3, of the Canadian Environmental Protection Act, 1999, Permit No. 4543-2-03313 is approved.

1. Permittee: Fraser River Pile & Dredge Ltd. — Mill & Timber Products, New Westminster, British Columbia.

2. Type of Permit: To load and to dispose at sea of waste and other matter.

3. Term of Permit: Permit is valid from February 14, 2003, to February 13, 2004.

4. Loading Site(s): Mill & Timber Products, Surrey, British Columbia, at approximately 49°12.95' N, 122°52.05' W.

5. Disposal Site(s): (a) Point Grey Disposal Site, 49°15.40' N, 123°22.10' W, at a depth of not less than 210 m; (b) Sand Heads Disposal Site, 49°06.00' N, 123°19.50' W, at a depth of not less than 70 m.

The following position fixing procedures must be followed to ensure disposal at the designated disposal site:

(i) The vessel must inform the appropriate Marine Communications and Traffic Services Centre (MCTS) upon departure from the loading site and inform MCTS that it is heading for a disposal site;
(ii) Upon arrival at a disposal site and prior to disposal, the vessel must again call MCTS to confirm its position. Disposal can proceed if the vessel is on the disposal site. If the vessel is not within the disposal site boundaries, MCTS will advise the bearing and distance to the site and advise when disposal can proceed; and
(iii) The vessel must inform MCTS when disposal has been completed, prior to leaving the disposal site.

6. Route to Disposal Site(s): Direct.

7. Method of Loading and Disposal: Clamshell dredging with disposal by bottom dump scow or end dumping.

8. Rate of Disposal: As required by normal operations.

9. Total Quantity to Be Disposed of: Not to exceed 18 000 m3.

10. Waste and Other Matter to Be Disposed of: Dredged material consisting of silt, sand, rock, wood waste and other materials typical to the approved loading site, except logs and usable wood. No woodwastes are to be sent to the Sand Heads Disposal Site.

11. Requirements and Restrictions:

11.1. The Permittee must notify the permit issuing office before commencement of the project as to the dates on which the loading or dumping will occur.

11.2. The Permittee must ensure that all contractors involved in the loading or disposal activity for which the permit is issued are made aware of any restrictions or conditions identified in the permit and of the possible consequences of any violation of these conditions. A copy of the permit and the letter of transmittal must be displayed at the disposal site and carried on all towing vessels and loading platforms or equipment involved in disposal at sea activities.

11.3. The fee prescribed by the Ocean Dumping Permit Fee Regulations (Site Monitoring) shall be paid by the Permittee in accordance with those Regulations.

11.4. Contact must be made with the Canadian Coast Guard, Regional Marine Information Centre (RMIC) regarding the issuance of a "Notice to Shipping." The RMIC is located at 2380-555 West Hastings Street, Vancouver, British Columbia V6B 5G3, (604) 666-6012 (Telephone), (604) 666-8453 (Facsimile), RMIC-PACIFIC@PAC.DFO-MPO.GC.CA (Electronic mail).

11.5. Any enforcement officer designated pursuant to subsection 217(1) of the Canadian Environmental Protection Act, 1999, shall be permitted to mount an electronic tracking device on any vessel that is engaged in the disposal at sea activities authorized by this permit. The Permittee shall take all reasonable measures to ensure there is no tampering with the tracking device and no interference with its operation. The tracking device shall be removed only by an enforcement officer or by a person with the written consent of an enforcement officer.

11.6. The Permittee must submit to the Regional Director, Environmental Protection Branch, within 30 days of the expiry of the permit, a list of all work completed pursuant to the permit, including the nature and quantity of material disposed of and the dates on which the activity occurred.

A. MENTZELOPOULOS

Environmental Protection

Pacific and Yukon Region

[1-1-o]

DEPARTMENT OF THE ENVIRONMENT

CANADIAN ENVIRONMENTAL PROTECTION ACT, 1999

New Source Emission Guidelines for Thermal Electricity Generation

The annexed New Source Emission Guidelines for Thermal Electricity Generation are a revised version of the former Thermal Power Generation Emissions — National Guidelines for New Stationary Sources which were issued May 15, 1993.

Whereas, pursuant to paragraph 54(1)(c) of the Canadian Environmental Protection Act, 1999, (see footnote 1)  the Minister of the Environment has formulated the annexed New Source Emission Guidelines for Thermal Electricity Generation;

And whereas the annexed Guidelines include emission limits for nitrogen oxides, particulate matter and sulphur dioxide based on the emissions performance achievable using current best available economically feasible technologies and strategies;

And whereas the annexed Guidelines reflect the intention of the Minister of the Environment to continually update these Guidelines to reflect advancements in emission control technologies and strategies over time.

Therefore, the Minister of the Environment, pursuant to subsection 54(1) of the Canadian Environmental Protection Act, 1999, is pleased to issue the annexed New Source Emission Guidelines for Thermal Electricity Generation and pursuant to subsection 54(4) direct that they be published in the Canada Gazette, Part I.

DAVID ANDERSON

Minister of the Environment

NEW SOURCE EMISSION GUIDELINES FOR THERMAL ELECTRICITY GENERATION

Foreword

1. During the development of the annexed Guidelines, representatives of the federal and provincial governments, environmental non-government organizations and industry were consulted regarding control strategies and emission limits for the air pollutants addressed in the Guidelines.

2. The Minister of the Environment recommends that the appropriate regulatory authorities adopt the annexed Guidelines as practical baseline standards for new fossil fuel-fired steam generating units within their jurisdictions. However, local conditions, such as density of industrial development, topography and other environmental considerations, may necessitate the adoption of more stringent requirements than those suggested in these Guidelines. The continual advancement in emission control technologies and strategies should also be taken into account.

Scope

3. (1) The annexed Guidelines indicate the quantities and concentrations above which nitrogen oxides, particulate matter and sulphur dioxide should not be emitted from fossil fuel-fired steam-driven electricity generating units, operated in whole or in part for the purpose of the sale of electricity to industry, commerce, or the public.

(2) The Guidelines are intended to apply to new generating units only. However, it is recognized that opportunities to reduce emissions may arise during major alterations to an existing generating unit. It is therefore recommended that an assessment of the feasibility of emission reduction measures be completed prior to commencing such alterations. This assessment should be undertaken by the owner of the unit in close consultation with the appropriate regulatory authority, and improved emission control measures should be implemented wherever feasible.

(3) The Guidelines are part of continuing efforts to diminish the emissions of air-polluting discharges to the atmosphere, and will contribute to that end by restricting such discharges from future additions to electric generating system capacity. The recommended emission limits are achievable using control methods now available to the industry for the abatement of the specified air pollutants.

Interpretation

4. In these Guidelines

"appropriate regulatory authority" means any federal, provincial or territorial government that has or could exercise regulatory or other authority over the emissions set out in these Guidelines. (autorité compétente de réglementation)

"averaging period" means a period for determining emission rates based on a 720-hour rolling average. (période de prise de la moyenne)

"continuous monitoring system" means the complete equipment for sampling, conditioning and analyzing emissions or process parameters and for recording data. (dispositif de surveillance en continu)

"first commercial operation" means the date of the first operation of a steam generating unit at which time electric generating capacity is electrically connected to the transmission and/or distribution systems for the use of tariff-paying customers. (début de 1'exploitation commerciale)

"fossil fuel" means natural gas, petroleum, coal, and any form of gaseous, liquid or solid fuel derived from such for the purpose of creating useful heat. (combustible fossile)

"generating unit" means a fossil fuel-fired steam combustion device used for the purpose of burning fossil fuel, at a rate in excess of 73 megajoules per second heat input, for the purpose of producing steam for utility electric generation. (générateur)

"gross energy output" means the gross useful work performed by the steam generated. For units generating only electricity, the gross useful work performed is the gross electrical output from the turbine/generator set. For cogeneration units, site-specific provisions for accounting for any useful thermal energy output supplied by the plant may be specified by the appropriate regulatory authority. (rendement énergétique brut)

"kg/MWh" means kilograms per megawatt-hour. (kg/MWh)

"net energy output" means gross energy output minus unit service power requirements. (rendement énergétique net)

"new generating unit" means any generating unit including a generating unit which replaces an existing generating unit with equivalent technology or with any other steam generating technology which is based on fossil fuel combustion, for which first commercial operation commences after April 1, 2003. (nouveau générateur)

"ng/J" means nanograms per joule. (ng/J)

"nitrogen oxides" means all oxides of nitrogen except nitrous oxide, collectively expressed as nitrogen dioxide. (oxydes d'azote)

"opacity" means the degree to which emissions reduce the transmission of light and obscure the view of an object in the background. (opacité)

"Protocol and Performance Specifications EPS 1/PG/7" means Protocols and Performance Specifications for Continuous Monitoring of Gaseous Emissions from Thermal Power Generation (EPS 1/PG/7), September 1993, published by the Department of the Environment, as may be amended from time to time. (Protocoles et spécifications des exigences en matière de performance SPE 1/PG/7)

"Reference Method EPS 1-AP-75-2" means Standard Reference Methods for Source Testing: Measurement of Opacity of Emissions from Stationary Sources (Reference Method EPS 1-AP-75-2), November 1977, published by the Department of the Environment as may be amended from time to time. (Méthodes de référence SPE 1-AP-75-2)

"Reference Method EPS 1/RM/8" means Reference Methods for Source Testing: Measurement of Releases of Particulate from Stationary Sources (Reference Method EPS/1/RM/8), December 1993, published by the Department of the Environment as may be amended from time to time. (Méthodes de référence SPE 1/RM/8)

"720-hour rolling average" means for each pollutant, the average of the consecutive hourly mean emission rates, determined for the preceding 720 hours of system operation. Intervals of zero emissions are not to be included in the calculation of rolling averages. (moyenne mobile sur 720 heures)

Emission Guidelines

5. (1) The hourly mean rate of discharge of sulphur dioxideemitted into the ambient air from a new generating unit, as determined over successive 720-hour rolling average periods, should not exceed any one of the following sets of final sulphur dioxide emission rates:

(a) 4.24 kg/MWh net energy output and 8% of the uncontrolled emission rate as determined under subsection (2); or
(b) 2.65 kg/MWh net energy output and 25% of the uncontrolled emission rate as determined under subsection (2);or
(c) 0.53 kg/MWh net energy output.

(2) The uncontrolled emission rate of sulphur dioxide from the generating unit in kilograms per megawatt-hour net energy output (kg/MWh) shall be calculated using the formula

(A/B) × C × (1 000 MJ/1 GJ) × D

where

A is the sulphur concentration in fuel expressed in the decimal form of a percentage, on a dry basis;

B is the higher heating value of fuel in megajoules per kilogram (MJ/kg);

C is a constant equal to 2, representing the ratio of molecular weight of sulphur dioxide to molecular weight of sulphur;

D is a constant equal to 10.6 GJ/MWh, representing the reference net plant heat rate in gigajoules per megawatt-hour.

6. The hourly mean rate of discharge of nitrogen oxides, expressed as NO2, emitted into the ambient air from a new generating unit when determined over successive 720-hour rolling average periods should not exceed the emission rate of 0.69 kg/MWh net energy output.

7. The hourly mean rate of discharge of particulate matter emitted into the ambient air from a new generating unit when determined over successive 720-hour rolling average periods should not exceed 0.095 kg/MWh net energy output.

Opacity

8. (1) Subject to subsection (2), a new generating unit should not emit visible emissions with opacity greater than 20%.

(2) A new generating unit may emit visible emissions with opacity greater than 20% but no more than 40% for a maximum of six (6) minutes in the sixty-(60) minute period following any increase in opacity above 20%.

Compliance

9. (1) Natural variations in coal constituents can cause emissions to vary and make enforcement on an hourly or daily basis impractical. However, calculating the 720-hour rolling average allows the regulatory authority to be informed daily, for each generating unit, of the maximum average emission rate in the previous 24 hours, since the rolling average must be calculated hourly, on the previous 720 hours' emission values.

(2) Subject to subsection (3), the emission guidelines set out in sections 5 to 8 may be exceeded in the event of

(a) malfunction or breakdown in air pollution control equipment; or
(b) start-up or shutdown in the operation of the source.

(3) These events should be minimized, both as to frequency of occurrence and duration of each event.

Emission Testing

10. (1) For the purposes of sections 5 to 8, emission tests should be conducted and a written report of results submitted to the appropriate regulatory authority within 180 days from first commercial operation of a generating unit and at such other times as the appropriate regulatory authority may require.

(2) Emission tests required under subsection (1) should be carried out in accordance with

(a) Protocol and Performance Specifications EPS 1/PG/7 for nitrogen oxides and sulphur dioxide;
(b) Reference Method EPS 1/RM/8 for particulate matter;
(c) Reference Method EPS 1-AP-75-2 for visible emissions.

Emission Monitoring

11. (1) A continuous monitoring system for measuring the opacity of emissions should be installed on each new generating unit that is fired with solid or liquid fossil fuel. The installation and operation of the system should be in accordance with the performance specification for transmissometer systems established by the appropriate regulatory authority.

(2) A continuous system for measuring sulphur dioxide should be installed on each new generating unit that is fired with solid or liquid fossil fuel. The installation and operation of the system should be in accordance with Protocol and Performance Specifications EPS 1/PG/7.

(3) A continuous monitoring system for measuring nitrogen oxides should be installed on each new generating unit. The installation and operation of the system should be in accordance with Protocol and Performance Specifications EPS 1/PG/7.

(4) All continuous monitoring systems should be installed, calibrated and operating prior to the emission tests required under subsections (l) to (3). During emission tests or within 30 days after the tests have been conducted, and at such other times as may be required, an evaluation of the performance of the continuous monitoring systems should be conducted in accordance with the requirements and procedures set out in Protocol and Performance Specifications EPS 1/PG/7. A written report of the results should be prepared and submitted, within sixty (60) days of the evaluation, to the appropriate regulatory authority.

Notification and Record Keeping

12. (1) The 720-hour rolling average emission rate for each pollutant included in these Guidelines should be sent to the appropriate regulatory authority at least every calendar quarter.

(2) Operators of new generating units should keep records of malfunction and breakdowns and should report each occurrence, at least every calendar quarter, to the appropriate regulatory authority. The appropriate regulatory authority should be furnished with written notification of

(a) the proposed construction, replacement, or major modification of a generating unit;
(b) the anticipated date of first commercial operation of the source, postmarked not less than 30 days prior to such date; and
(c) the date of any performance tests and evaluations of continuous monitoring system performance, postmarked not less than 30 days prior to such date.

[1-1-o]

DEPARTMENT OF THE ENVIRONMENT

CANADIAN ENVIRONMENTAL PROTECTION ACT, 1999

Notice with Respect to Substances in the National Pollutant Release Inventory for 2003

Notice is hereby given, pursuant to subsection 46(1) of the Canadian Environmental Protection Act, 1999, that for the purpose of conducting research, creating an inventory of data, formulating objectives and codes of practice, issuing guidelines or assessing or reporting on the state of the environment, any person who owns or operates a facility described in Schedule 2 to this notice during the 2003 calendar year, and who possesses or who may reasonably be expected to have access to information described in Schedule 3, shall provide the Minister of the Environment with this information no later than June 1, 2004. Where appropriate, terms contained in this notice have been defined in Schedule 4.

Responses or enquiries concerning this notice shall be addressed to one of the following addresses:

British Columbia and Yukon
National Pollutant Release Inventory
Environment Canada
401 Burrard Street, Suite 201
Vancouver, British Columbia
V6C 3S5
Telephone: (604) 666-3221 / 666-3890
Facsimile: (604) 666-6800
Electronic mail: NPRI_PYR@ec.gc.ca

Manitoba, Saskatchewan, Alberta,
Northwest Territories and Nunavut
National Pollutant Release Inventory
Environment Canada
Twin Atria No. 2, Room 200
4999 98 Avenue
Edmonton, Alberta
T6B 2X3
Telephone: (780) 951-8989
Facsimile: (780) 495-2615
Electronic mail: NPRI_PNR@ec.gc.ca

Ontario
National Pollutant Release Inventory
Environmental Protection Branch — Ontario Region
Environment Canada
4905 Dufferin Street, 2nd Floor
Downsview, Ontario
M3H 5T4
Telephone: (416) 739-5955 / 739-5886 / 739-4602 / 739-4608
Facsimile: (416) 739-4326
Electronic mail: NPRI_ONTARIO@ec.gc.ca

Quebec
National Pollutant Release Inventory
Environment Canada
105 McGill Street, 4th Floor
Montréal, Quebec
H2Y 2E7
Telephone: (514) 283-7303 / 496-1832
Facsimile: (514) 496-6982
Electronic mail: INRP_QC@ec.gc.ca

Newfoundland and Labrador, Prince Edward Island, New Brunswick and Nova Scotia
National Pollutant Release Inventory
Environment Canada
Queen Square, 16th Floor
45 Alderney Drive
Dartmouth, Nova Scotia
B2Y 2N6
Telephone: (902) 426-4482 / 426-4805 / 426-5037
Facsimile: (902) 426-8373
Electronic mail: NPRI_ATL@ec.gc.ca

Headquarters
National Pollutant Release Inventory
Environment Canada
Place Vincent Massey, 9th Floor
351 Saint-Joseph Boulevard
Hull, Quebec
K1A 0H3
Telephone: (819) 953-1656
Facsimile: (819) 994-3266
Electronic mail: NPRI@ec.gc.ca

This notice comes into force on January 4, 2003 and remains in force until January 4, 2006. Pursuant to subsection 46(8) of the Canadian Environmental Protection Act, 1999, persons to whom this notice applies shall keep copies of the required information, together with any calculations, measurements and other data on which the information is based at the facility to which it relates or at that facility's parent company, located in Canada, for a period of three years from the date this notice comes into force.

The Minister of the Environment intends to publish, in part, the information submitted in response to this notice. Pursuant to sections 51 and 313 of the Canadian Environmental Protection Act, 1999, any person who provides information in response to this notice may submit, with their information, a written request that it be treated as confidential based on the reasons set out in section 52 of the Act. The Minister may also disclose, in accordance with sections 315, 316 and 317 of the Canadian Environmental Protection Act, 1999, information submitted in response to this notice.

BARRY STEMSHORN

Assistant Deputy Minister

Environmental Protection Service

On behalf of the Minister of the Environment

SCHEDULE 1

National Pollutant Release Inventory Substances

PART 1

GROUP 1 SUBSTANCES

Name CAS Registry Number (see footnote a)
1. Acetaldehyde 75-07-0
2. Acetonitrile 75-05-8
3. Acetophenone 98-86-2
4. Acrolein 107-02-8
5. Acrylamide 79-06-1
6. Acrylic acid 79-10-7 (see footnote 2) 
7. Acrylonitrile 107-13-1
8. Alkanes, C6-18, chloro 68920-70-7
9. Alkanes, C10-13, chloro 85535-84-8
10. Allyl alcohol 107-18-6
11. Allyl chloride 107-05-1
12. Aluminum 7429-90-5 (see footnote 3) 
13. Aluminum oxide 1344-28-1 (see footnote 4) 
14. Ammonia (total) (see footnote 5)  (see footnote b) 
15. Aniline 62-53-3 (see footnote 6)
16. Anthracene 120-12-7
17. Antimony (see footnote 7) (see footnote c)
18. Asbestos (see footnote 8) 1332-21-4
19. Benzene 71-43-2
20. Benzoyl chloride 98-88-4
21. Benzoyl peroxide 94-36-0
22. Benzyl chloride 100-44-7
23. Biphenyl 92-52-4
24. Bis(2-ethylhexyl) adipate 103-23-1
25. Bis(2-ethylhexyl) phthalate 117-81-7
26. Boron trifluoride 7637-07-2
27. Bromine 7726-95-6
28. 1-Bromo-2-chloroethane 107-04-0
29. Bromomethane 74-83-9
30. 1,3-Butadiene 106-99-0
31. 2-Butoxyethanol 111-76-2
32. Butyl acrylate 141-32-2
33. i-Butyl alcohol 78-83-1
34. n-Butyl alcohol 71-36-3
35. sec-Butyl alcohol 78-92-2
36. tert-Butyl alcohol 75-65-0
37. Butyl benzyl phthalate 85-68-7
38. 1,2-Butylene oxide 106-88-7
39. Butyraldehyde 123-72-8
40. C.I. Acid Green 3 4680-78-8
41. C.I. Basic Green 4 569-64-2
42. C.I. Basic Red 1 989-38-8
43. C.I. Direct Blue 218 28407-37-6
44. C.I. Disperse Yellow 3 2832-40-8
45. C.I. Food Red 15 81-88-9
46. C.I. Solvent Orange 7 3118-97-6
47. C.I. Solvent Yellow 14 842-07-9
48. Calcium cyanamide 156-62-7
49. Calcium fluoride 7789-75-5
50. Carbon disulphide 75-15-0
51. Carbon tetrachloride 56-23-5
52. Carbonyl sulphide 463-58-1
53. Catechol 120-80-9
54. CFC-11 75-69-4
55. CFC-12 75-71-8
56. CFC-13 75-72-9
57. CFC-114 76-14-2
58. CFC-115 76-15-3
59. Chlorendic acid 115-28-6
60. Chlorine 7782-50-5
61. Chlorine dioxide 10049-04-4
62. Chloroacetic acid (see footnote 9) 79-11-8
63. Chlorobenzene 108-90-7
64. Chloroethane 75-00-3
65. Chloroform 67-66-3
66. Chloromethane 74-87-3
67. 3-Chloro-2-methyl-1-propene 563-47-3
68. 3-Chloropropionitrile 542-76-7
69. Chromium (see footnote 10) (see footnote d)
70. Cobalt (see footnote 11) (see footnote e)
71. Copper (see footnote 12) (see footnote f)
72. Cresol (see footnote 13)  1319-77-3
73. Crotonaldehyde 4170-30-3
74. Cumene 98-82-8
75. Cumene hydroperoxide 80-15-9
76. Cyanides (see footnote 14) (see footnote g)
77. Cyclohexane 110-82-7
78. Cyclohexanol 108-93-0
79. Decabromodiphenyl oxide 1163-19-5
80. 2,4-Diaminotoluene (see footnote 15) 95-80-7
81. 2,6-Di-t-butyl-4-methylphenol 128-37-0
82. Dibutyl phthalate 84-74-2
83. o-Dichlorobenzene 95-50-1
84. p-Dichlorobenzene 106-46-7
85. 3,3-Dichlorobenzidine dihydrochloride 612-83-9
86. 1,2-Dichloroethane 107-06-2
87. Dichloromethane 75-09-2
88. 2,4-Dichlorophenol (see footnote 16)  120-83-2
89. 1,2-Dichloropropane 78-87-5
90. Dicyclopentadiene 77-73-6
91. Diethanolamine (see footnote 17) 111-42-2
92. Diethyl phthalate 84-66-2
93. Diethyl sulphate 64-67-5
94. Dimethylamine 124-40-3
95. N,N-Dimethylaniline (see footnote 18)  121-69-7
96. N,N-Dimethylformamide 68-12-2
97. Dimethyl phenol 1300-71-6
98. Dimethyl phthalate 131-11-3
99. Dimethyl sulphate 77-78-1
100. 4,6-Dinitro-o-cresol (see footnote 19) 534-52-1
101. 2,4-Dinitrotoluene 121-14-2
102. 2,6-Dinitrotoluene 606-20-2
103. Dinitrotoluene (see footnote 20) 25321-14-6
104. Di-n-octyl phthalate 117-84-0
105. 1,4-Dioxane 123-91-1
106. Diphenylamine 122-39-4
107. Epichlorohydrin 106-89-8
108. 2-Ethoxyethanol 110-80-5
109. 2-Ethoxyethyl acetate 111-15-9
110. Ethyl acrylate 140-88-5
111. Ethylbenzene 100-41-4
112. Ethyl chloroformate 541-41-3
113. Ethylene 74-85-1
114. Ethylene glycol 107-21-1
115. Ethylene oxide 75-21-8
116. Ethylene thiourea 96-45-7
117. Fluorine 7782-41-4
118. Formaldehyde 50-00-0
119. Formic acid 64-18-6
120. Halon 1211 353-59-3
121. Halon 1301 75-63-8
122. HCFC-22 75-45-6
123. HCFC-122 (see footnote 21)  41834-16-6
124. HCFC-123 (see footnote 22)  34077-87-7
125. HCFC-124 (see footnote 23)  63938-10-3
126. HCFC-141b 1717-00-6
127. HCFC-142b 75-68-3
128. Hexachlorocyclopentadiene 77-47-4
129. Hexachloroethane 67-72-1
130. Hexachlorophene 70-30-4
131. n-Hexane 110-54-3
132. Hydrazine (see footnote 24)  302-01-2
133. Hydrochloric acid 7647-01-0
134. Hydrogen cyanide 74-90-8
135. Hydrogen fluoride 7664-39-3
136. Hydrogen sulphide 7783-06-4
137. Hydroquinone (see footnote 25) 123-31-9
138. Iron pentacarbonyl 13463-40-6
139. Isobutyraldehyde 78-84-2
140. Isophorone diisocyanate 4098-71-9
141. Isoprene 78-79-5
142. Isopropyl alcohol 67-63-0
143. p,p'-Isopropylidenediphenol 80-05-7
144. Isosafrole 120-58-1
145. Lithium carbonate 554-13-2
146. Maleic anhydride 108-31-6
147. Manganese (see footnote 26)  (see footnote h) 
148. 2-Mercaptobenzothiazole 149-30-4
149. Methanol 67-56-1
150. 2-Methoxyethanol 109-86-4
151. 2-Methoxyethyl acetate 110-49-6
152. Methyl acrylate 96-33-3
153. Methyl tert-butyl ether 1634-04-4
154. p,p'-Methylenebis(2-chloroaniline) 101-14-4
155. 1,1-Methylenebis(4-isocyanatocyclohexane) 5124-30-1
156. Methylenebis(phenylisocyanate) 101-68-8
157. p,p'-Methylenedianiline 101-77-9
158. Methyl ethyl ketone 78-93-3
159. Methyl iodide 74-88-4
160. Methyl isobutyl ketone 108-10-1
161. Methyl methacrylate 80-62-6
162. N-Methylolacrylamide 924-42-5
163. 2-Methylpyridine 109-06-8
164. N-Methyl-2-pyrrolidone 872-50-4
165. Michler's ketone (see footnote 27) 90-94-8
166. Molybdenum trioxide 1313-27-5
167. Naphthalene 91-20-3
168. Nickel (see footnote 28) (see footnote i)
169. Nitrate ion (see footnote 29) (see footnote j) 
170. Nitric acid 7697-37-2
171. Nitrilotriacetic acid (see footnote 30) 139-13-9
172. p-Nitroaniline 100-01-6
173. Nitrobenzene 98-95-3
174. Nitroglycerin 55-63-0
175. p-Nitrophenol (see footnote 31) 100-02-7
176. 2-Nitropropane 79-46-9
177. N-Nitrosodiphenylamine 86-30-6
178. Nonylphenol and its ethoxylates (see footnote 32) (see footnote k)
179. Octylphenol and its ethoxylates (see footnote 33) (see footnote l) 
180. Paraldehyde 123-63-7
181. Pentachloroethane 76-01-7
182. Peracetic acid (see footnote 34) 79-21-0
183. Phenol (see footnote 35)  108-95-2
184. p-Phenylenediamine (see footnote 36) 106-50-3
185. o-Phenylphenol (see footnote 37) 90-43-7
186. Phosgene 75-44-5
187. Phosphorus (see footnote 38) 7723-14-0
188. Phosphorus (total) (see footnote 39)  
189. Phthalic anhydride 85-44-9
190. Polymeric diphenylmethane diisocyanate 9016-87-9
191. Potassium bromate 7758-01-2
192. Propargyl alcohol 107-19-7
193. Propionaldehyde 123-38-6
194. Propylene 115-07-1
195. Propylene oxide 75-56-9
196. Pyridine (see footnote 40)  110-86-1
197. Quinoline (see footnote 41) 91-22-5
198. p-Quinone 106-51-4
199. Safrole 94-59-7
200. Selenium (see footnote 42) (see footnote m)
201. Silver (see footnote 43) (see footnote n) 
202. Sodium fluoride 7681-49-4
203. Sodium nitrite 7632-00-0
204. Styrene 100-42-5
205. Styrene oxide 96-09-3
206. Sulphur hexafluoride 2551-62-4
207. Sulphuric acid 7664-93-9
208. 1,1,1,2-Tetrachloroethane 630-20-6
209. 1,1,2,2-Tetrachloroethane 79-34-5
210. Tetrachloroethylene 127-18-4
211. Tetracycline hydrochloride 64-75-5
212. Thiourea 62-56-6
213. Thorium dioxide 1314-20-1
214. Titanium tetrachloride 7550-45-0
215. Toluene 108-88-3
216. Toluene-2,4-diisocyanate 584-84-9
217. Toluene-2,6-diisocyanate 91-08-7
218. Toluenediisocyanate (see footnote 44) 26471-62-5
219. 1,2,4-Trichlorobenzene 120-82-1
220. 1,1,2-Trichloroethane 79-00-5
221. Trichloroethylene 79-01-6
222. Triethylamine 121-44-8
223. 1,2,4-Trimethylbenzene 95-63-6
224. 2,2,4-Trimethylhexamethylene diisocyanate 16938-22-0
225. 2,4,4-Trimethylhexamethylene diisocyanate 15646-96-5
226. Vanadium (see footnote 45)  7440-62-2
227. Vinyl acetate 108-05-4
228. Vinyl chloride 75-01-4
229. Vinylidene chloride 75-35-4
230. Xylene (see footnote 46)  1330-20-7
231. Zinc (see footnote 47) (see footnote o)

GROUP 2 SUBSTANCES

Name CAS Registry Number
232. Mercury (see footnote 48) (see footnote p)

GROUP 3 SUBSTANCES

Name CAS Registry Number
233. Cadmium (see footnote 49) (see footnote q)

GROUP 4 SUBSTANCES

column 1 Name CAS Registry Number
234. Arsenic (see footnote 50) (see footnote r)
235. Hexavalent chromium compounds (see footnote s)  
236. Lead (see footnote 51)  (see footnote 52) (see footnote t)
237. Tetraethyl lead 78-00-2

PART 2

Name CAS Registry Number
238. Benzo(a)anthracene 56-55-3
239. Benzo(a)phenanthrene 218-01-9
240. Benzo(a)pyrene 50-32-8
241. Benzo(b)fluoranthene 205-99-2
242. Benzo(e)pyrene 192-97-2
243. Benzo(g,h,i)perylene 191-24-2
244. Benzo(j)fluoranthene 205-82-3
245. Benzo(k)fluoranthene 207-08-9
246. Dibenz(a,j)acridine 224-42-0
247. Dibenzo(a,h)anthracene 53-70-3
248. Dibenzo(a,i)pyrene 189-55-9
249. 7H-Dibenzo(c,g)carbazole 194-59-2
250. Fluoranthene 206-44-0
251. Indeno(1,2,3-c,d)pyrene 193-39-5
252. Perylene 198-55-0
253. Phenanthrene 85-01-8
254. Pyrene 129-00-0

PART 3

Name CAS Registry Number
255. Hexachlorobenzene 118-74-1
256. Dioxins and furans (see footnote 53) (see footnote u)

PART 4 — CRITERIA AIR CONTAMINANTS (CACs)

Name CAS Registry Number
257. Carbon monoxide 630-08-0
258. Oxides of nitrogen (expressed as NO2) 11104-93-1
259. PM2.5 (see footnote v) 
260. PM10 (see footnote w) 
261. Sulphur dioxide 7446-09-5
262. Total particulate matter (see footnote x)
263. Volatile organic compounds (see footnote 54) (see footnote y)

PART 5 — SELECTED VOLATILE ORGANIC COMPOUNDS WITH ADDITIONAL REPORTING REQUIREMENTS

Individual Substances

Name CAS Registry Number
264. Acetylene 74-86-2
265. Adipic acid 124-04-9
266. Aniline (see footnote 55) 62-53-3
267. Benzene 71-43-2
268. 1,3-Butadiene 106-99-0
269. 2-Butoxyethanol 111-76-2
270. n-Butyl acetate 123-86-4
271. Chlorobenzene 108-90-7
272. p-Dichlorobenzene 106-46-7
273. Dimethylether 115-10-6
274. Ethyl alcohol 64-17-5
275. Ethyl acetate 141-78-6
276. Ethylene 74-85-1
277. Ethylene dichloride 107-06-2
278. Formaldehyde 50-00-0
279. n-Hexane 110-54-3
280. Isopropyl alcohol 67-63-0
281. D-Limonene 5989-27-5
282. Methyl alcohol 67-56-1
283. Methyl ethyl ketone 78-93-3
284. 2-Methyl-3-hexanone 7379-12-6
285. Methyl isobutyl ketone 108-10-1
286. Myrcene 123-35-3
287. Beta-Phellandrene 555-10-2
288. Phenyl isocyanate 103-71-9
289. Alpha-Pinene 80-56-8
290. Beta-Pinene 127-91-3
291. Propane 74-98-6
292. Propylene 115-07-1
293. Styrene 100-42-5
294. 1,2,4-Trimethylbenzene 45-20-8
295. Trimethylfluorosilane 420-56-4
296. Toluene 108-88-3
297. Vinyl acetate 108-05-4
298. Anthraquinone (see footnote 56) (see footnote z)
299. Butane (see footnote 57)   
300. Butene (see footnote 58)  25167-67-3
301. Cycloheptane (see footnote 59) (see footnote aa)
302. Cyclohexene (see footnote 60) (see footnote ab)
303. Cyclooctane (see footnote 61)  (see footnote ac)
304. Decane (see footnote 62) (see footnote ad)
305. Dihydronapthalene (see footnote 63) (see footnote ae)
306. Dodecane (see footnote 64) (see footnote af)
307. Heptane (see footnote 65) (see footnote ag)
308. Hexane (see footnote 66) (see footnote ah)
309. Hexene (see footnote 67) 25264-93-1
310. Methylindan (see footnote 68) 27133-93-3
311. Nonane (see footnote 69)  (see footnote ai)
312. Octane (see footnote 70)  (see footnote aj)
313. Pentane (see footnote 71) (see footnote ak)
314. Pentene (see footnote 72)  (see footnote al)
315. Terpene (see footnote 73) 68956-56-9
316. Trimethylbenzene (see footnote 74) 25551-13-7
317. Xylene (see footnote 75)  1330-20-7

Other Groups and Mixtures

Name CAS Registry Number
318. Creosote 8001-58-9
319. Heavy aromatic solvent naphtha 64742-94-5
320. Light aromatic solvent naphtha 64742-95-6
321. Mineral spirits 64475-85-0
322. Naphtha 8030-30-6
323. Stoddard solvent 8052-41-3

SCHEDULE 2

Criteria for Reporting

GENERAL

Persons who must report

If a person who owns or operates a facility with respect to which information was submitted in response to the Notice with Respect to Substances in the National Pollutant Release Inventory for 2002 determines that the facility does not meet the criteria for reporting set out in Parts 1 through 5 in this Schedule, the person shall notify the Minister of the Environment that the facility does not meet these criteria. If the ownership orthe person who operates a facility as described in this Schedule changes during the 2003 calendar year, the person who owns or operates the facility as of December 31, 2003, must report for the entire 2003 calendar year by June 1, 2004. If operations at a facility are terminated during the 2003 calendar year, the last owner or operator of that facility is required to report for the portion of the 2003 calendar year during which the facility was in operation, by June 1, 2004.

1. The following activities, to which the 20 000-hour employee threshold does not apply, are identified for the purposes of Parts 1 to 5:

(a) non-hazardous solid waste incineration of 26 tonnes or more of waste per year, including small combustion units, conical burners and beehive burners;
(b) biomedical or hospital waste incineration of 26 tonnes or more of waste per year;
(c) hazardous waste incineration;
(d) sewage sludge incineration;
(e) wood preservation;
(f) terminal operations;
(g) discharge of treated or untreated wastewater from a wastewater collection system with an annual average discharge of 10 000 cubic meters or more per day, into surface waters.

2. A substance listed in Schedule 1 shall not be included in calculating its prescribed mass reporting threshold if the substance is

(a) manufactured, processed or otherwise used for the exploration of oil or gas, or drilling of oil or gas wells; or
(b) contained in:

(i) articles that are processed or otherwise used;
(ii) materials used as structural components of the facility but not the process equipment;
(iii) materials used in routine janitorial or facility grounds maintenance;
(iv) materials used for personal use by employees or other persons;
(v) materials used for the purpose of maintaining motor vehicles operated by the facility;
(vi) intake water or intake air, such as water used for process cooling or air used either as compressed air or for combustion; or
(vii) road dust.

3. (1) A substance listed in Schedule 1 shall not be included in calculating its prescribed mass reporting threshold if the substance is manufactured, processed or otherwise used in an activity listed below:

(a) education or training of students, such as at universities, colleges and schools;
(b) research or testing;
(c) maintenance and repair of transportation vehicles, such as automobiles, trucks, locomotives, ships or aircraft, except painting and stripping of vehicles or their components, or the rebuilding or remanufacturing of vehicle components;
(d) distribution, storage, or retail sale of fuels, except as part of the terminal operations;
(e) wholesale or retail sale of articles or products, if the substance is not released to the environment during normal use at the facility;
(f) retail sale of the substance;
(g) growing, harvesting, or management of renewable natural resources, such as fisheries, forestry or agriculture, except processing or otherwise using renewable natural resources;
(h) mining, except processing or otherwise using mined materials; or
(i) the practice of dentistry.

(2) Despite subsection (1), if a substance is listed in Part 4 or 5 of Schedule 1, it shall be included in calculating its prescribed mass reporting threshold if the substance was released to air as a result of the combustion of fuel in stationary combustion equipment.

PART 1

CRITERIA FOR REPORTING SUBSTANCES LISTED IN PART 1 OF SCHEDULE 1

Facilities for which a report is required for a substance listed in Part 1 of Schedule 1:

4. (1) A contiguous facility or offshore installation where, during 2003:

(a) either was used for an activity listed in section 1, or where employees worked a total of 20 000 hours or more;
(b) any substance listed in Part 1 of Schedule 1 was manufactured, processed or otherwise used in a quantity equal to or greater than the quantity set out in column 2 of Table 1 corresponding to the group in which the substance is listed; and
(c) the concentration by weight of the substance was equal to or greater than the concentration by weight of the substance set out in column 3 of Table 1 corresponding to the group in which the substance is listed, unless the substance is a by-product or there is no corresponding value set out in column 3 of Table 1 for the substance.

(2) For the purposes of paragraph (1)(b), by-products shall be included in the calculation of the mass reporting threshold set out in column 2 of Table 1, regardless of concentration.

5. For the purposes of this Part, the mass reporting threshold for a substance listed in Part 1 of Schedule 1 shall be calculated as follows:

(a) for a substance that is qualified with the footnote "and its salts," use the molecular weight of the of the acid or the base and not the total weight of the salt;
(b) for a substance that is qualified with the footnote "and its compounds," use the pure element and the equivalent weight of the element contained in any substance, alloy or mixture except for lead and its compounds contained in stainless steel, brass or bronze alloys;
(c) for ammonia (total), use the ammonium ion (NH4+) in solution expressed as ammonia and include with ammonia;
(d) for vanadium, include the pure element and the equivalent weight of the element contained in any substance or mixture except when contained in an alloy; and
(e) for phosphorus (total), express as phosphate on a mass basis.

Table 1: Mass Reporting Threshold and Concentration for Substances Listed in Part 1 of Schedule 1




Item
Column 1

Substances in Part 1
of Schedule 1
Column 2

Mass Reporting Threshold
Column 3

Concentration by Weight
1. Group 1 Substances 10 tonnes 1%
2. Group 2 Substance 5 kilograms N/A
3. Group 3 Substance 5 kilograms 0.1%
4. Group 4 Substances 50 kilograms 0.1%

PART 2

CRITERIA FOR REPORTING SUBSTANCES LISTED IN PART 2 OF SCHEDULE 1

Facilities for which a report is required for a substance listed in Part 2 of Schedule 1:

6. A contiguous facility or offshore installation where, during 2003:

(a) either was used for an activity listed in section 1, or where employees worked a total of 20 000 hours or more;
(b) any substance listed in Part 2 of Schedule 1 was incidentally manufactured; and
(c) the sum total of the substances listed in Part 2 of Schedule 1 released on site or to surface waters or transferred off site as a result of incidental manufacture is 50 kilograms or more.

7. A contiguous facility where, during 2003,

(a) the contiguous facility was used for wood preservation and creosote was used, at any time, for that purpose; and
(b) any substance listed in Part 2 of Schedule 1 was released on-site or to surface waters or transferred off-site as a result of wood preservation using creosote.

PART 3

CRITERIA FOR REPORTING SUBSTANCES LISTED IN PART 3 OF SCHEDULE 1

Facilities for which a report is required for a substance listed in Part 3 of Schedule 1:

8. A contiguous facility or offshore installation where, during 2003:

(a) either was used for an activity listed in section 1, or where employees worked a total of 20 000 hours or more; and
(b) the contiguous facility was engaged in one or more of the following activities:

(i) non-hazardous solid waste incineration of 26 tonnes or more of waste per year, including small combustion units, conical burners and beehive burners;
(ii) biomedical or hospital waste incineration of 26 tonnes or more of waste per year;
(iii) hazardous waste incineration;
(iv) sewage sludge incineration;
(v) base metals smelting;
(vi) smelting of secondary aluminum;
(vii) smelting of secondary lead;
(viii) manufacturing of iron using a sintering process;
(ix) operation of electric arc furnaces in steel foundries;
(x) operation of electric arc furnaces in steel manufacturing;
(xi) production of magnesium;
(xii) manufacturing of portland cement;
(xiii) production of chlorinated organic solvents or chlorinated monomers;
(xiv) combustion of fossil fuel in a boiler unit with a nameplate capacity of 25 megawatts or greater of electricity, for the purpose of producing steam for the production of electricity;
(xv) combustion of hog fuel originating from logs that were transported or stored in salt water in the pulp and paper sector;
(xvi) combustion of fuel in kraft liquor boilers used in the pulp and paper sector; or
(xvii) wood preservation using pentachlorophenol.

PART 4

CRITERIA FOR REPORTING SUBSTANCES LISTED IN PART 4 OF SCHEDULE 1

Facilities for which a report is required for a substance listed in Part 4 of Schedule 1:

9. A contiguous facility or offshore installation where, during 2003:

(a) either was used for an activity listed in section 1, or where employees worked a total of 20 000 hours or more; and
(b) the substance set out in column 1 of Table 2 was released to air in a quantity equal to or greater than the quantity set out in column 2 of Table 2 for that substance.

10. (1) A facility that, during 2003:

(a) was a contiguous facility or offshore installation where employees worked a total of less than 20 000 hours, or was a pipeline installation; and
(b) released to air a substance listed in Part 4 of Schedule 1 from the combustion of fuel in stationary combustion equipment at the facility, in a quantity equal to or greater than the quantity set out in column 2 of Table 2 for that substance.

(2) Despite subsection (1), a report for a substance listed in Part 4 of Schedule 1 is not required if:

(a) the substance is only released to air from stationary, external-combustion equipment;
(b) the cumulative nameplate capacity of that equipment is less than 10 million British thermal units per hour; and
(c) the only type of fuel combusted in that equipment is commercial grade natural gas, liquified petroleum gas, Number 1 or 2 fuel oil or any combination thereof.

11. When calculating the mass reporting threshold for oxides of nitrogen (expressed as NO2), express the oxides of nitrogen as nitrogen dioxide on a mass basis.

Table 2: Mass Reporting Threshold for Substances Listed in Part 4 of Schedule 1



Item
Column 1

Substances in Part 4 of Schedule 1
Column 2

Mass Reporting Threshold
1. Carbon monoxide 20 tonnes
2. Oxides of nitrogen (expressed as NO2) 20 tonnes
3. PM2.5 0.3 tonnes
4. PM10 0.5 tonnes
5. Sulphur dioxide 20 tonnes
6. Total particulate matter 20 tonnes
7. Volatile organic compounds 10 tonnes

PART 5

CRITERIA FOR REPORTING SUBSTANCES LISTED IN PART 5 OF SCHEDULE 1

Facilities for which a report is required for a substance or class of substances listed in Part 5 of Schedule 1:

12. A facility where a report is required under section 9 or 10 for volatile organic compounds, and where during 2003, a substance or class of substances listed in Part 5 was released to air in a quantity equal to or greater than 1 tonne.

SCHEDULE 3

Types of Information Subject to Notice and Manner of Reporting

GENERAL

1. The information reported shall be based on the best available data and information that the person possesses or to which the person may reasonably be expected to have access.

2. (1) If a substance listed in Schedule 1 is not included in calculating its prescribed mass reporting threshold pursuant to section 2 of Schedule 2, no information is required to be reported in respect of that substance that is contained in articles, materials or intake water or air described in section 2 of Schedule 2 or that is manufactured, processed, or otherwise used for the exploration for oil or gas, or drilling of oil or gas wells.

(2) If a substance listed in Schedule 1 is not included in calculating its prescribed mass reporting threshold pursuant to section 3 of Schedule 2, no information is required to be reported in respect of that substance that resulted from the manufacture, process, or otherwise use of an activity described in subsection 3(1) of Schedule 2.

PART 1

FACILITY INFORMATION

3. Identification of the reporting facility subdivided by:

(a) the reporting company's legal and trade name, facility name (if applicable) and address;
(b) the NPRI identification number;
(c) the number of full-time employee equivalents;
(d) the Dun and Bradstreet number (where available);
(e) the two- and four-digit Canadian Standard Industrial Classification (SIC) codes and the four-digit U.S. SIC code;
(f) the two- and four-digit North American Industry Classification System (NAICS) codes and the six-digit NAICS Canada code;
(g) the name, position, address and telephone number of the public contact (if applicable);
(h) the name, position, address and telephone number of the technical contact;
(i) the name, position, address and telephone number of the individual co-ordinating the submission of the report (if applicable);
(j) the name, position and address of the official signing the Statement of Certification; and
(k) the legal name(s) of the parent companies if applicable, their addresses, and their percentage of ownership of the reporting company (where available), and their Dun and Bradstreet number (where available).

4. A statement indicating whether an independent contractor completed the report, and if so, the name, company name, telephone number and address of the independent contractor.

5. A Statement of Certification signed by an authorized signing officer of the company indicating that the person has reviewed the documents, has exercised due diligence to ensure that the information submitted is true, accurate and complete, and is based on the best available data and information.

6. Identification of reported information for which a request is being made to treat the information as confidential pursuant to sections 51 and 313 of the Canadian Environmental Protection Act, 1999, and the reasons for the request in accordance with section 52 of the Act.

7. Identification of the activities listed in section 1 of Schedule 2, for which the facility was used, if any.

8. Identification of the activities listed in paragraph 8(b) in Part 3 of Schedule 2, in which the facility was engaged, if any.

9. Identification of whether the facility was used for wood preservation and whether creosote was used, at any time, for that purpose.

10. Identification of whether, during the 2003 calendar year, the facility had prepared or was implementing any pollution prevention plans, and if so, whether any were pollution prevention plans:

(a) required by a notice under the Canadian Environmental Protection Act, 1999;
(b) prepared or implemented for another government or under another Act of Parliament; or
(c) prepared or implemented by the facility on a voluntary basis.

PART 2

INFORMATION REQUIRED FOR SUBSTANCES LISTED IN PARTS 1 THROUGH 3 OF SCHEDULE 1

11. For each substance or class of substances listed in Parts 1 through 3 of Schedule 1 for which the reporting criteria have been satisfied, report the following:

(a) its identity, including, if applicable, its Chemical Abstracts Service Registry Number;
(b) the nature of the manufacturing activity, if applicable, subdivided by: on-site use or processing, sale or distribution, as a by-product or as an impurity;
(c) the nature of the processing activity, if applicable, subdivided by: as a reactant, as a formulation component, as an article component, for repackaging only, or as a by-product;
(d) the nature of the other use activity, if applicable, subdivided by: as a physical or chemical processing aid, as a manufacturing aid, for ancillary or other use, or as a by-product;
(e) the quantity released on site to air, subdivided by: stack releases or point releases, storage or handling releases, fugitive releases, spills, or other non-point releases;
(f) the quantity released on site to underground injection;
(g) the quantity released to surface waters, subdivided by: direct discharges, spills, or leaks, the name of the receiving surface water bodies and the quantity released to each receiving surface water body;
(h) the quantity released on site to land, subdivided by: landfill, land treatment, spills, leaks, or other;
(i) the quantity transferred off-site for disposal, subdivided by: physical treatment, chemical treatment, biological treatment, incineration or thermal treatment, landfill, storage, municipal sewage treatment plant, underground injection, or land treatment, and the name and address of each receiving facility and the quantity transferred to each facility;
(j) the quantity transferred off-site for recycling, subdivided by: energy recovery, recovery of solvents, recovery of organic substances (not solvents), recovery of metals and metal compounds, recovery of inorganic materials (not metals), recovery of acids or bases, recovery of catalysts, recovery of pollution abatement residues, refining or re-use of used oil, or other, and the name and address of each receiving facility and the quantity transferred to each facility;
(k) the method of estimation used to determine the quantities reported pursuant to paragraphs (e) through (j), subdivided by: monitoring or direct measurement, mass balance, emission factors, engineering estimates, or no releases on site, releases to surface waters or transfers off-site;
(l) the quarterly breakdown of total releases (on site and to surface waters) during 2003, by percentage;
(m) the reasons for changes in quantities of releases on site and releases to surface waters from the previous year, subdivided by: changes in production levels, changes in estimation methods, pollution-prevention activities, changes in on-site treatment, changes in off-site transfers for disposal, changes in off-site transfers for recycling, other (specify), no significant change or no change, or first year reporting the substance;
(n) the reasons for the transfer off-site for disposal or for recycling, subdivided by: production residues, off-specification products, expiration date has passed, contaminated materials, unusable parts or discards, pollution abatement residues, machining or finishing residues, site remediation residues, or other;
(o) the reasons for changes in quantities transferred off-site for disposal from the previous year, subdivided by: changes in production levels, changes in estimation methods, pollution prevention activities, changes in on-site treatment, changes in off-site transfers for recycling, other (specify), no significant change or no change, or first year reporting the substance;
(p) the reasons for changes in quantities transferred off-site for recycling from the previous year, subdivided by: changes in production levels, changes in estimation methods, pollution-prevention activities, changes in on-site treatment, changes in off-site transfers for disposal, other (specify), no significant change or no change, or first year reporting the substance;
(q) the anticipated total releases on site and to surface waters, off-site transfers for disposal and off-site transfers for recycling for 2004, 2005, and 2006; and
(r) the pollution prevention methods used and, for each method reported, the specific type of method used, subdivided as follows:

(i) materials or feedstock substitution, subdivided by: increased purity of materials, substituted materials, or other (specify);
(ii) product design or reformulation, subdivided by: changed product specifications, modified design or composition, modified packaging, or other (specify);
(iii) equipment or process modifications, subdivided by: modified equipment, layout, or piping, used different process catalyst, instituted better controls on operating bulk containers, changed from small volume containers to bulk containers, modified stripping/cleaning equipment, changed to mechanical stripping/cleaning devices, changed to aqueous cleaners, modified or installed rinse systems, improved rinse equipment design, improved rinse equipment operation, modified spray systems or equipment, improved application techniques, changed from spray to other system, other (specify);
(iv) spill and leak prevention, subdivided by: improved storage or stacking procedures, improved procedures for loading, unloading, and transfer operations, installed overflow alarms or automatic shut-off valves, installed vapor recovery systems, implemented inspection or monitoring program of potential spill or leak sources, modified containment procedures, improved draining procedures, other (specify);
(v) on-site reuse or recycling, subdivided by: instituted recirculation within a process, or other (specify);
(vi) improved inventory management or purchasing techniques, further subdivided by: instituted procedures to ensure that materials do not stay in inventory beyond shelf-life, initiated testing of outdated material, eliminated shelf-life requirements for stable materials, instituted better labeling procedures, instituted clearinghouse to exchange materials, instituted improved purchasing procedures, other (specify);
(vii) training or good operating practices, subdivided by: improved maintenance scheduling, record keeping or procedures, changed production schedule to minimize equipment and feedstock changeovers, training related to pollution prevention, other (specify);
(viii) other (specify); or
(ix) no pollution prevention activities.

For the purposes set out in this notice, any person to whom this notice applies shall provide the information required by this Part respecting substances in Part 1 of Schedule 1 in the following manner:

12. Report the information for a substance listed in Part 1 of Schedule 1 as follows:

(a) for a substance that is qualified with the footnote "and its salts", report the molecular weight of the of the acid or the base and not the total weight of the salt;
(b) for a substance that is qualified with the footnote "and its compounds", report the pure element and the equivalent weight of the element contained in any substance, alloy or mixture, except for lead and its compounds contained in stainless steel, brass or bronze alloys;
(c) for ammonia (total), express the ammonium ion (NH4+) in solution as ammonia, and report together with ammonia;
(d) for vanadium, report the pure element and the equivalent weight of the element contained in any substance or mixture, except when contained in an alloy; and
(e) for phosphorus (total), express as phosphate on a mass basis.

13. Report information in respect of substances listed in Group 1 in Part 1 of Schedule 1 in tonnes.

14. Report information in respect of substances listed in Groups 2, 3 and 4 in Part 1 of Schedule 1 in kilograms.

For the purposes set out in this notice, any person to whom this notice applies shall provide the information required by this Part respecting substances in Part 2 of Schedule 1 in the following manner:

15. If information on individual substances listed in Part 2 of Schedule 1 is not available, report information for the group as a whole.

16. Report information in respect of substances listed in Part 2 of Schedule 1 in kilograms.

For the purposes set out in this notice, any person to whom this notice applies shall provide the information required by this Part respecting substances in Part 3 of Schedule 1 in the following manner:

17. Only report information for a substance listed in Part 3 of Schedule 1 that resulted from the incidental manufacture of the substance from the activities identified in subparagraphs 8(b)(i) through (xvi) inPart 3 of Schedule 2, or that ispresent as a contaminant in pentachlorophenol for the activity listed in subparagraph 8(b)(xvii) in Part 3 of Schedule 2.

18. For the purposes of paragraphs 11(e) through (j), if the method of estimation for the quantity released on-site, released to surface waters, or transferred off-site for a substance listed in Part 3 of Schedule 1 is monitoring or direct measurement:

(a) indicate in the report whether the concentration of the substance released on-site, released to surface waters or transferred off-site was less than, equal to or greater than the estimated level of quantification set out in section 19 for that substance in the corresponding medium; and
(b) reporting the quantity released on-site, released to surface waters or transferred off-site is optional if the concentration of the substance released on-site, released to surface waters or transferred off-site is less than the estimated level of quantification set out in section 19 for that substance in the corresponding medium.

19. (1) For the purpose of section 18, the estimated level of quantification values for hexachlorobenzene listed in Part 3 of Schedule 1 are:

(a) 6 nanograms of hexachlorobenzene per cubic metre of gaseous material;
(b) 70 nanograms of hexachlorobenzene per litre of liquid material; and
(c) 2 nanograms of hexachlorobenzene per gram of solid material.

(2) For the purpose of section 18, the estimated level of quantification values for dioxins and furans listed in Part 3 of Schedule 1 are:

(a) 32 picograms of toxicity equivalents of dioxins and furans per cubic metre of gaseous material;
(b) 20 picograms of toxicity equivalents of dioxins and furans per litre of liquid material; and
(c) 9 picograms of toxicity equivalents of dioxins and furans per gram of solid material.

20. Report information in respect of hexachlorobenzene listed in Part 3 of Schedule 1 in grams.

21. Report information in respect of dioxins and furans in Part 3 of Schedule 1 in grams of toxicity equivalents (TEQ).

22. If information necessary to estimate the quantity of a substance listed in Part 3 of Schedule 1 released on-site, released to surface waters or transferred off-site is not available, report that the information is not available.

PART 3

INFORMATION REQUIRED FOR SUBSTANCES LISTED IN PART 4 OF SCHEDULE 1

23. For each substance or class of substances listed in Part 4 of Schedule 1 for which the reporting criteria set out in Part 4 of Schedule 2 have been satisfied, report the following:

(a) its identity, including, if applicable, its Chemical Abstracts Service Registry Number;
(b) the quantity released on-site to air, subdivided by: stack releases or point releases, storage or handling releases, fugitive releases, spills or other non-point releases;
(c) for each stack with a height equal to or greater than 50 metres above grade where the substance is released to air from the stack in a quantity equal to or greater than the quantity set out in column 2 of Table 1 corresponding to that substance:

(i) the quantity of the substance that was released from the stack; and
(ii) the stack height above grade, theequivalent diameter of the stack, theaverageexit velocity, and theaverageexit temperature for each stack;

(d) the method of estimation used to determine the quantities reported pursuant to paragraph (b) and subparagraph (c)(i), subdivided by: monitoring or direct measurement, mass balance, emission factors, engineering estimates, or no releases to air;
(e) the monthly breakdown of total releases to air during 2003, by percentage;
(f) the reasons for changes in quantities of releases to air from the previous year, subdivided by: changes in production levels, changes in estimation methods, pollution-prevention activities, changes in on-site treatment, other (specify), no significant change or no change, or first year reporting the substance;
(g) the anticipated total releases to air for 2004, 2005, and 2006; and
(h) the pollution prevention information described in paragraph 11(r) in Part 2.

24. If the reporting criteria in Part 4 of Schedule 2 are satisfied for a substance listed in Part 4 of Schedule 1, report the representative daily and weekly operating schedule of the facility for each month.

Table 1: Minimum Quantity Released from Stack During 2003 Calendar Year





Item Number
Column 1



Substance Name
Column 2

Minimum
Quantity
Released from Stack
1. Carbon monoxide 5 tonnes
2. Oxides of nitrogen (expressed as NO2) 5 tonnes
3. PM2.5 0.15 tonnes
4. PM10 0.25 tonnes
5. Sulphur dioxide 5 tonnes
6. Total particulate matter 5 tonnes
7. Volatile organic compounds 5 tonnes

For the purposes set out in this notice, any person to whom this notice applies shall provide the information respecting substances in Part 4 of Schedule 1 required by this Part in the following manner:

25. If a facility satisfies the reporting criteria set out in section 10 in Part 4 of Schedule 2, only report information for releases of the Part 4 substance from the stationary combustion equipment at the facility.

26. Report information respecting oxides of nitrogen (expressed as NO2) by expressing the oxides of nitrogen as nitrogen dioxide on a mass basis.

27. Report information in respect of substances listed in Part 4 of Schedule 1, in tonnes.

PART 4

INFORMATION REQUIRED FOR SUBSTANCES LISTED IN PART 5 OF SCHEDULE 1

28. For each substance or class of substances listed in Part 5 of Schedule 1, for which the reporting criteria set out in Part 5 of Schedule 2 have been satisfied, report the following:

(a) its identity, including, if applicable, its Chemical Abstracts Service Registry Number;
(b) the quantity released from each stack with a height equal to or greater than 50 meters where the quantity of volatile organic compounds was released to air from the stack was equal to or greater than 5 tonnes; and
(c) the quantity of all other releases to air excluding those quantities reported under paragraph (b).

29. If the reporting criteria set out in Part 4 of Schedule 2 have been satisfied for volatile organic compounds, identify whether the reactivity of the group of volatile organic compounds released to air that were not required to be reported as individual substances or classes of substances under Parts 1 or 5 of Schedule 2, is high, medium, low, or unknown reactivity.

For the purposes set out in this notice, any person to whom this notice applies shall provide the information respecting substances in Part 5 of Schedule 1 required by this Part in the following manner:

30. If a facility satisfies the reporting criteria set out in section 10 in Part 4 of Schedule 2 for volatile organic compounds, only report information for releases of the Part 5 substance from the stationary combustion equipment at the facility.

31. Report information in respect of a substance listed in Part 5, in tonnes.

SCHEDULE 4

Definitions

1. The following definitions apply to this notice and its schedules:

"alloy" includes metal products containing two or more elements as a solid solution, intermetallic compounds, and mixtures of metallic phases. « alliage »

"article" means a manufactured item that does not release a substance, listed in Schedule 1, under normal conditions of processing or other use. « article »

"base metal" means copper, lead, nickel and zinc. « métal commun »

"by-product" means a substance, listed in Schedule 1, which is incidentally manufactured, processed or otherwise used at the facility at any concentration, and released on-site to the environment, released to surface waters or transferred off-site for disposal. « sous-produit »

"CAS Registry Number" and "CAS No." mean the Chemical Abstracts Service Registry Number. « numéro d'enregistrement CAS » or « numéro du CAS »

"contiguous facility" means all buildings, equipment, structures and stationary items that are located on a single site or on contiguous or adjacent sites and that are owned or operated by the same person and that function as a single integrated site and includes wastewater collection systems that discharge treated or untreated wastewater into surface waters. « installation contiguë »

"disposal" means the final disposal of the material (e.g., landfill), or treatment (e.g., stabilization) prior to final disposal. « élimination »

"employee" includes:

(a) a person employed at the facility;
(b) an owner who performs work on site at the facility; and
(c) a person who performs work on site at the facility on a routine basis that is related to the normal operations of the facility, for the period of time the person is performing that work, such as contractors. « employé »

"external-combustion equipment" means any equipment with a combustion process that occurs at atmospheric pressure and with excess air. « appareil à combustion externe »

"facility" means a contiguous facility, a pipeline installation, or an offshore installation. « installation »

"fossil fuel" means fuel that is in a solid or liquid state at standard temperature and pressure, such as coal, petroleum or any solid or liquid fuel derived from such. « combustible fossile »

"full-time employee equivalent" means the unit obtained by dividing by 2 000 hours, the sum of:

(a) the total hours worked by persons employed at the facility, and the total hours of paid vacation and of sick leave taken by persons employed at the facility;
(b) the hours worked on site at the facility by the owner of the facility, if not employed by the facility; and
(c) the hours worked on site at the facility by a person who performs work on a routine basis related to the normal operations of the facility, such as contractors. « équivalent d'employé à temps plein »

"level of quantification" means, in respect of a substance, the lowest concentration that can be accurately measured using sensitive but routine sampling and analytical methods. « niveau de dosage »

"manufacture" means to produce, prepare, or compound a substance listed in Schedule 1 and includes the coincidental production of a substance, listed in Schedule 1, as a by-product as a result of the manufacturing, processing or other use of other substances. « fabrication »

"offshore installation" means an offshore drilling unit, production platform or ship, or subsea installation attached or anchored to the continental shelf of Canada in connection with the exploitation of oil or gas. « installation extracôtière »

"other use" includes any use or disposal of a substance, listed in Schedule 1, relevant to the purpose of the facility which is not included under the definitions of "manufacture" or "process". « autre utilisation »

"parent company" means the highest level company or group of companies that own or directly control the reporting facility. « société mère »

"pipeline installation" means a collection of equipment situated at a single site, used in the operation of a natural gas transmission or distribution pipeline. « installation de pipeline »

"PM2.5" means any particulate matter with a diameter less than or equal to 2.5 microns. « PM2,5 »

"PM10" means any particulate matter with a diameter less than or equal to 10 microns. « PM10  »

"pollution prevention" means the use of processes, practices, materials, products, substances or energy that avoid or minimize the creation of pollutants and waste, and reduce the overall risk to the environment or human health. « prévention de la pollution »

"process" means the preparation of a substance, listed in Schedule 1, after its manufacture, for commercial distribution and includes preparation of a substance in the same physical state or chemical form as that received by the facility, or preparation which produces a change in physical state or chemical form. « traitement »

"recycling" includes any activity that prevents a material or a component of the material from becoming a material destined for disposal. « recyclage »

"secondary aluminum" means aluminum-bearing scrap or aluminum-bearing materials. « aluminium de récupération »

"secondary lead" means lead-bearing scrap or lead-bearing materials, other than lead-bearing concentrates derived from a mining operation. « plomb de récupération »

"terminal operations" means

(a) the use of storage tanks and associated equipment at a site used to store or transfer crude oil, artificial crude or intermediates of fuel products into or out of a pipeline; or
(b) operating activities of a primary distribution installation normally equipped with floating roof tanks that receives gasoline by pipeline, railcar, marine vessel or directly from a refinery. « opérations de terminal »

"total particulate matter" means any particulate matter with a diameter less than 100 microns. « particules totales »

"toxicity equivalent" commonly referred to as TEQ, means a mass or concentration which is a sum of the masses or concentrations of individual congeners of polychlorinated dibenzop-dioxins and polychlorinated dibenzofurans multiplied by weighting factors set out in the Guide for Reporting to the National Pollutant Release Inventory — 2003. « équivalents toxiques »

"volatile organic compounds" means volatile organic compounds as defined in the Proposed Order Adding Toxic Substances to Schedule 1 to the Canadian Environmental Protection Act, 1999, published in the Canada Gazette, Part I, Vol. 136, No. 30 (Ottawa, Saturday, July 27, 2002). « composés organiques volatils »

"wood preservation" means the use of a preservative for the preservation of wood by means of heat or pressure treatment, or both, and includes the manufacture, blending, or reformulation of wood preservatives for that purpose. « préservation du bois »

EXPLANATORY NOTE
(This note is not part of the notice.)

Consultations were undertaken during 2002 on the issue of reporting of greenhouse gases (GHGs) to the NPRI. The Government is committed to requiring reporting of GHG emissions, beginning with reporting on 2004 emissions. The reporting will be mandatory, verifiable, and include suitable provisions for reporting at the facility level. The Government wil consult with stakeholders, including Aboriginal peoples of Canada industry and environmental non-government organizations, on detailed reporting requirements, including options for the reporting mechanism and public availability of the data, recognizing the ongoing discussion on the Climate Change Plan for Canada.

Persons to whom this notice applies should register at one of the aforementioned addresses to receive a copy of the Guide for Reporting to the National Pollutant Release Inventory — 2003, other applicable guidance material and the 2003 reporting software.

The Guide for Reporting to the National Pollutant Release Inventory — 2003, other applicable guidance material and the 2003 reporting software will be mailed to facilities for which reports are received for the 2002 reporting year. Correspondence will be addressed to the company coordinator identified in the 2002 NPRI report; if none was indicated, the materials will be sent to the technical contact. Notwithstanding the above, obtaining the guidance materials and the reporting software for 2003 is the responsibility of the person required to report to the 2003 National Pollutant Release Inventory. Those who have not received their copies by April 14, 2004, should contact Environment Canada at one of the aforementioned addresses.

[1-1-o]

DEPARTMENT OF INDUSTRY

CANADA CORPORATIONS ACT

Letters Patent

Notice is hereby given that, pursuant to the provisions of the Canada Corporations Act, Letters Patent have been issued to:

File Number Name of Company Head Office Effective Date
412524-0 AFRICAN CHRISTIAN MISSIONS OF CANADA Regional Municipality of Peel, Ont. 25/11/2002
410816-7 ARH HEALTHCARE FOUNDATION Edmonton, Alta. 03/12/2002
411949-5 APPALACHIAN CORRIDOR Bolton-Ouest, Que. 31/10/2002
411914-2 ARTS INTERNATIONAL SCHOOLS SOCIETY Vancouver, B.C. 04/11/2002
412981-4 ASSOCIATION OF CANADIAN TEXTILE RECYCLERS Burlington, Ont. 29/11/2002
412178-3 BurundiRéalités International Inc (BRI) Ottawa (Ont.) 12/11/2002
412519-3 CALVARY BAPTIST CHURCH — GUELPH Guelph, Ont. 25/11/2002
412225-9 CANADA PACIFIC MINISTRIES County of Yale, B.C. 07/11/2002
412247-0 Canadian Association of Commercial Diving Educators Nanaimo, B.C. 01/11/2002
412768-4 CANADIAN PIGEON FANCIERS' ASSOCIATION INC. Sherwood Park, Alta. 22/11/2002
412463-4 CANADIAN RETINOBLASTOMA SOCIETY Port Hope, Ont. 21/11/2002
410621-1 CANADIAN SERBIAN CHAMBER OF COMMERCE Mississauga, Ont. 02/12/2002
412773-1 CEPN-ECHNOLOGIE Wendake (Qué.) 29/11/2002
412157-1 CHEETAH CONSERVATION FUND CANADA City of Toronto, Ont. 13/11/2002
412721-8 COMMUNICATIONS DIALOGUE DIRECT Montréal (Qué.) 29/11/2002
412151-1 DENE NATION Yellownkife, N.W.T. 13/11/2002
412709-9 DOWNSVIEW PARK FOUNDATION City of Toronto, Ont. 28/11/2002
412196-1 EASY RECITE ARABIC ACADEMY Maple, Ont. 12/11/2002
412546-1 Federal Association for the Advancement of Visible Minorities — FAAVM Ottawa, Ont. 15/11/2002
412255-1 FEDERATED HEALTH CHARITIES CORPORATION Toronto, Ont. 06/11/2002
411818-9 FOUNDATION FOR THE EDUCATION OF CHILDREN IN UGANDA (F.E.C.U.) Montréal, Que. 29/10/2002
412512-6 GOOD SAMARTIN OKANAGAN SHUSWAP (A Lutheran Social Service Organization) City of Edmonton, Alta. 25/11/2002
412697-1 IGALI FOUNDATION INC. Surrey, B.C. 27/11/2002
412209-7 INNOCENTRE GUELPH CORPORATION City of Guelph, Ont. 08/11/2002
410974-1 INTERNATIONAL HEALTHCARE SERVICE EXCELLENCE ASSOCIATION Calgary, Alta. 26/09/2002
412351-4 LUXEMBOURG CHAMBER OF COMMERCE IN TORONTO City of Toronto, Ont. 15/11/2002
412400-6 MARS INSTITUTE Victoria, B.C. 15/11/2002
412207-1 McWONG FOUNDATION Greater Vancouver Regional District, B.C. 05/11/2002
412319-1 MFDA Investor Protection Corporation Toronto, Ont. 14/11/2002
412471-5 NATIONAL CAPITAL COALITION FOR PEOPLE AND DOGS City of Ottawa, Ont. 21/11/2002
412392-1 NEW CHARISMATIC INTERNATIONAL MINISTRY Toronto, Ont. 19/11/2002
411944-4 PALM MINISTRY ASSOCIATION Sherwood Park, Alta. 01/11/2002
412675-1 PAL RETIREMENT/EXTENDED CARE CORPORATION Toronto, Ont. 22/11/2002
413079-1 PHILLIPIAN FOUNDATION Toronto, Ont. 06/12/2002
412886-9 BRIDGES OF LOVE TO THE NATIONS Hull (Qué.) 02/12/2002
413078-2 PROCURE ALLIANCE ALLIANCE PROCURE Judicial District of Montréal, Que. 01/01/2003
412693-9 PROFESSIONAL DEVELOPMENT CENTRE FOR MEMBERS OF CANADIAN ADMINISTRATIVE TRIBUNALS Ottawa, Ont. 27/11/2002
411340-3 CMA — CHRISTIAN MUTUAL AID & Professional Resources for Couples & Families, Inc. Région métropolitaine de
Toronto (Ont.)
09/10/2002
393827-1 REDEEMER BIBLE CHURCH, NIAGARA FALLS Regional Municipality of Niagara, Ont. 28/08/2002
412767-6 Réseau des anciens des Jeux du Commerce Montréal (Qué.) 22/11/2002
412983-1 SALT RIVER YOUTH AND EDUCATIONAL FOUNDATION Salt River Reserve, Fort Smith N.W.T. 28/11/2002
411382-9 ST. JOSEPH'S FINANCIAL SERVICES ASSOCIATION City of Hamilton, Ont. 26/11/2002
412164-3 THE BAKER FAMILY FOUNDATION (LONDON) London, Ont. 12/11/2002
412525-8 THE BAY STREET CHILDREN'S FOUNDATION Toronto, Ont. 25/11/2002
411849-9 THE DEEP RIVER AND DISTRICT HOSPITAL FOUNDATION Town of Deep River, Ont. 30/10/2002
410801-9 The Friends of McCaig Elementary School Rosemere, Que. 27/09/2002
412473-1 THE GATHERING (WOODSTOCK) Woodstock, Ont. 21/11/2002
412772-2 THE INSTITUTE FOR THE STUDY OF MARRIAGE, LAW AND CULTURE Montréal, Que. 22/11/2002
412674-2 THE MARGARET CULLIGAN FOUNDATION Toronto, Ont. 26/11/2002
412902-4 THE STEVEN AND SANDRA MINTZ FAMILY FOUNDATION Metropolitan Region of
Montréal, Que.
03/12/2002
412495-2 THE SYNTAX FOUNDATION Metropolitan Region of
Montréal, Que.
25/11/2002
412515-1 THOPAGA FOUNDATION Waterloo, Ont. 25/11/2002
412344-1 VANCOUVER INTERNATIONAL SCULPTURE BIENNALE Greater Vancouver Regional
District, B.C.
14/11/2002

December 18, 2002

ROBERT WEIST

Director

Incorporation and Disclosure

Services Branch

For the Minister of Industry

[1-1-o]

DEPARTMENT OF INDUSTRY

CANADA CORPORATIONS ACT

Supplementary Letters Patent

Notice is hereby given that, pursuant to the provisions of the Canada Corporations Act, supplementary letters patent have been issued to:

File No. Company Name Date of S.L.P.
387181-9 BIRTHRIGHT ISRAEL FOUNDATION OF CANADA 06/11/2002
410242-8 CANADA KOREA VETERANS FOUNDATION 29/11/2002
097647-4 EUROVANGELISM 12/11/2002
361098-5 FIRST NATIONS ADULT AND HIGHER EDUCATION CONSORTIUM 12/11/2002
370893-4 INTERNATIONAL CHINA CONCERN (CANADA) 15/11/2002
409210-4 Kids In Distress Society 22/11/2002
304400-9 THE CANADIAN COUNCIL ON CONTINUING EDUCATION IN PHARMACY 30/10/2002

December 18, 2002

ROBERT WEIST

Director

Incorporation and Disclosure

Services Branch

For the Minister of Industry

[1-1-o]

DEPARTMENT OF INDUSTRY

CANADA CORPORATIONS ACT

Supplementary Letters Patent — Name Change

Notice is hereby given that, pursuant to the provisions of the Canada Corporations Act, supplementary letters patent have been issued to:

File No. Old Company Name New Company Name Date of S.L.P.
354921-6 CANADIAN ROCKIES REVIVAL MINISTRIES Mountain Springs Ministries 15/11/2002
119122-5 CENTRE FOR STUDY OF INSURANCE OPERATIONS Centre for Study of Insurance Operations 04/11/2002
409942-7 COMPOSERS' ALLIANCE Musical Alliance 25/09/2002
377882-7 FALLS RIVER OF BLESSING CHURCH GATEWAY CHRISTIAN FELLOWSHIP OF SOUTHERN ONTARIO 07/05/2002
410231-2 The Consensus Party of Canada THE NEW CONSENSUS PARTY OF CANADA 30/10/2002
386258-5 THE MACEDONIAN FUND FOR NATIONAL RIGHTS Macedonian National Fund 12/11/2002

December 18, 2002

ROBERT WEIST

Director

Incorporation and Disclosure

Services Branch

For the Minister of Industry

[1-1-o]

Footnote 1 

S.C. 1999, c. 33

Footnote a 

The Chemical Abstracts Service (CAS) Registry Number is the property of the American Chemical Society and any use or redistribution, except as required in supporting regulatory requirements and/or for reports to the Government when the information and the reports are required by law or administrative policy, is not permitted without the prior, written permission of the American Chemical Society.

Footnote 2 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 3 

"fume or dust."

Footnote 4 

"fibrous forms.

Footnote 5 

"Ammonia (total)" means the total of both of ammonia (NH3 — CAS No. 7664-41-7) and the ammonium ion (NH4+) in solution.

Footnote b 

No single CAS No. applies to this substance.

Footnote 6 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 7 

"and its compounds".

Footnote c 

No single CAS No. applies to this substance.

Footnote 8 

"friable form"

Footnote 9 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 10 

"and its compounds" except hexavalent chromium compounds.

Footnote d 

No single CAS No. applies to this substance.

Footnote 11 

"and its compounds".

Footnote e 

No single CAS No. applies to this substance.

Footnote 12 

"and its compounds".

Footnote f 

No single CAS No. applies to this substance.

Footnote 13 

"all isomers" including the individual isomers of cresol: m-cresol (CAS No. 108-39-4), o-cresol (CAS No. 95-48-7) and p-cresol (CAS No. 106-44-5).

Footnote 14 

"ionic. "

Footnote g 

No single CAS No. applies to this substance.

Footnote 15 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 16 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 17 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 18 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 19 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 20 

"mixed isomers."

Footnote 21 

"all isomers" including, but not limited to, HCFC-122 (CAS No. 354-21-2).12.

Footnote 22 

"all isomers" including, but not limited to, HCFC-123 (CAS No. 306-83-2), and HCFC-123a (CAS No. 90454-18-5).

Footnote 23 

"all isomers" including, but not limited to, HCFC-124 (CAS No. 2837-89-0), and HCFC-124a (CAS No. 354-25-6).

Footnote 24 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 25 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 26 

"and its compounds".

Footnote h 

No single CAS No. applies to this substance.

Footnote 27 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 28 

"and its compounds".

Footnote i 

No single CAS No. applies to this substance.

Footnote 29 

"in solution at a pH of 6.0 or greater."

Footnote j 

No single CAS No. applies to this substance.

Footnote 30 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 31 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 32 

Includes nonylphenol, its ethoxylates and derivatives with CAS No.'s: 104-40-5; 25154-52-3; 84852-15-3; 1323-65-5; 26523-78-4; 28987-17-9; 68081-86-7; 68515-89-9; 68515-93-5; 68081-86-1; 104-35-8; 20427-84-3; 26027-38-3; 27177-05-5; 27177-08-8; 28679-13-2; 27986-36-3; 37251-69-7; 7311-27-5; 9016-45-9; 27176-93-8; 37340-60-6; 51811-79-1; 51938-25-1; 68412-53-3; 9051-57-4; 37205-87-1; 68412-54-4; 127087-87-01.

Footnote k 

Includes octylphenol and its ethoxylates with CAS No.'s: 140-66-9; 1806-26-4; 27193-28-8; 68987-90-6; 9002-93-1; 9036-19-5.

Footnote 33 

Includes octylphenol and its ethoxylates with CAS No.'s: 140-66-9; 1806-26-4; 27193-28-8; 68987-90-6; 9002-93-1; 9036-19-5.

Footnote l 

No single CAS No. applies to this substance.

Footnote 34 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 35 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 36 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 37 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 38 

"yellow and white"

Footnote 39 

Does not include phosphorus (yellow or white) with CAS No. 7723-14-0.

Footnote 40 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 41 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 42 

"and its compounds".

Footnote m 

No single CAS No. applies to this substance.

Footnote 43 

"and its compounds".

Footnote n 

No single CAS No. applies to this substance.

Footnote 44 

"mixed isomers."

Footnote 45 

"(except when in an alloy) and its compounds."

Footnote 46 

"all isomers" including the individual isomers of xylene: m-xylene (CAS No. 108-38-3), o-xylene (CAS No. 95-47-6) and p-xylene (CAS No. 106-42-3).

Footnote 47 

"and its compounds".

Footnote o 

No single CAS No. applies to this substance.

Footnote 48 

"and its compounds".

Footnote p 

No single CAS No. applies to this substance.

Footnote 49 

"and its compounds".

Footnote q 

No single CAS No. applies to this substance.

Footnote 50 

"and its compounds".

Footnote r 

No single CAS No. applies to this substance.

Footnote s 

No single CAS No. applies to this substance.

Footnote 51 

"and its compounds", except tetraethyl lead (CAS No. 78-00-2).

Footnote 52 

Does not include lead (and its compounds) contained in stainless steel, brass or bronze alloys.

Footnote t 

No single CAS No. applies to this substance.

Footnote 53 

This class of substances, known as polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans, is restricted to the following congeners:
2,3,7,8-Tetrachlorodibenzo-p-dioxin (CAS No. 1746.01.6);
1,2,3,7,8-Pentachlorodibenzo-p-dioxin (CAS No. 40321.76.4);
1,2,3,4,7,8-Hexachlorodibenzo-p-dioxin (CAS No. 39227.28.6);
1,2,3,7,8,9-Hexachlorodibenzo-p-dioxin (CAS No. 19408.74.3);
1,2,3,6,7,8-Hexachlorodibenzo-p-dioxin (CAS No. 57653.85.7);
1,2,3,4,6,7,8-Heptachlorodibenzo-p-dioxin (CAS No. 35822.46.9);
Octachlorodibenzo-p-dioxin (CAS No. 3268.87.9);
2,3,7,8-Tetrachlorodibenzofuran (CAS No. 51207.31.9);
2,3,4,7,8-Pentachlorodibenzofuran (CAS No. 57117.31.4);
1,2,3,7,8-Pentachlorodibenzofuran (CAS No. 57117.41.6);
1,2,3,4,7,8-Hexachlorodibenzofuran (CAS No. 70648.26.9);
1,2,3,7,8,9-Hexachlorodibenzofuran (CAS No. 72918.21.9);
1,2,3,6,7,8-Hexachlorodibenzofuran (CAS No. 57117.44.9);
2,3,4,6,7,8-Hexachlorodibenzofuran (CAS No. 60851.34.5);
1,2,3,4,6,7,8-Heptachlorodibenzofuran (CAS No. 67562.39.4);
1,2,3,4,7,8,9-Heptachlorodibenzofuran (CAS No. 55673.89.7); and
Octachlorodibenzofuran (CAS No. 39001.02.0).

Footnote u 

No single CAS No. applies to this substance.

Footnote v 

No single CAS No. applies to this substance.

Footnote w 

No single CAS No. applies to this substance.

Footnote x 

No single CAS No. applies to this substance.

Footnote 54 

Defined in Schedule 4 to this notice. This class of substances is not limited to the substances listed in Schedule 1 but includes all substances that satisfy the definition of volatile organic compounds in Schedule 4 to this notice.

Footnote y 

No single CAS No. applies to this substance.

Footnote 55 

"and its salts" - The CAS No. corresponds to the weak acid or base. However, this substance includes the salts of these weak acids and bases.

Footnote 56 

"all isomers."

Footnote z 

No single CAS No. applies to this substance.

Footnote 57 

"all isomers."

Footnote aa 

No single CAS No. applies to this substance.

Footnote 58 

"all isomers."

Footnote 59 

"all isomers."

Footnote ab 

No single CAS No. applies to this substance.

Footnote 60 

"all isomers."

Footnote ac 

No single CAS No. applies to this substance.

Footnote 61 

"all isomers."

Footnote ad 

No single CAS No. applies to this substance.

Footnote 62 

"all isomers."

Footnote ae 

No single CAS No. applies to this substance.

Footnote 63 

"all isomers."

Footnote af 

No single CAS No. applies to this substance.

Footnote 64 

"all isomers."

Footnote ag 

No single CAS No. applies to this substance.

Footnote 65 

"all isomers."

Footnote ah 

No single CAS No. applies to this substance.

Footnote 66 

"all isomers", excluding n-hexane (CAS No. 110-54-3).

Footnote ai 

No single CAS No. applies to this substance.

Footnote 67 

"all isomers."

Footnote 68 

"all isomers."

Footnote 69 

"all isomers."

Footnote aj

No single CAS No. applies to this substance.

Footnote 70 

"all isomers."

Footnote ak 

No single CAS No. applies to this substance.

Footnote 71 

"all isomers."

Footnote al 

No single CAS No. applies to this substance.

Footnote 72 

"all isomers."

Footnote am

No single CAS No. applies to this substance.

Footnote 73 

"all isomers."

Footnote 74 

"all isomers", excluding 1,2,4-trimethylbenzene (CAS No. 45-20-8).

Footnote 75 

"all isomers."


NOTICE:
The format of the electronic version of this issue of the Canada Gazette was modified in order to be compatible with extensible hypertext markup language (XHTML 1.0 Strict).